McDATA Enterprise Operating System Скачать руководство пользователя страница 53

Страница: 53 / 328

CLI Commands

2-9

config

Purpose

This command sets the enabled state of the OpenTrunking feature.
The OpenTrunking feature key must be installed in order to enable
open trunking.

Parameters

This command has one parameter.

Command Example

Root>

config features openTrunking 1

NOTE:

The command

perf.openTrunking.setState

on page 2-107 has

functionality that is identical to this command.

config.features.show

Syntax

show

Purpose

This command shows the product feature information configured for
this switch.

Parameters

This command has no parameters.

Command Example

Root>

config features show

Output

The product feature data is displayed as a table that includes the
following properties.

openTrunkingState

This parameter can be set to

enable

disable

the OpenTrunking feature. Boolean 1 and 0
may be substituted as values.

Installed Feature
Set

The feature set installed using a feature key.
Only installed keys are displayed.

Feature

Individual features within each set. In many
cases, there is only one feature within each
feature set.

State

The state of the individual feature. Fabric-wide
features are displayed as

Active/Inactive

Features related to the switch are displayed as

Enabled/Disabled

Содержание Enterprise Operating System









































































































































































































































































































































Результаты поиска

Содержание Enterprise Operating System

Отзывы:

Похожие инструкции для Enterprise Operating System

Бренды по названию

Популярные бренды

McDATA Enterprise Operating System, Руководство пользователя

Результаты поиска

Содержание Enterprise Operating System

Отзывы:

Похожие инструкции для Enterprise Operating System

Бренды по названию

Популярные бренды