McDATA Enterprise Operating System Скачать руководство пользователя страница 60

Страница: 60 / 328

2-16

Enterprise Operating System Command Line Interface User Manual

config

The output from the config.fencing.show Policy_1 command displays
as follows:

Name:

Policy_1

Ports:

E ports

Type:

Protocol Error

Limit:

Period:

300 seconds

State:

Disabled

config.fencing.showTypeTable

Syntax

showTypeTable

Purpose

This command displays the table of different fencing types that can
be assigned to a policy. This table is used for reference only.

Parameters

This command has no parameters.

Command Example

Root>

config fencing showTypeTable

Output Example

The output from the config.fencing.showTypeTable command
displays as follows:

Number

Fencing Policy Types

---------------------------------
1

Protocol Errors

config.ficonCUPZoning.addControlHost

Syntax

addControlHost hostNodeWwn

Purpose

This command adds a control host to the Control Host List used to
determine the FICON host(s) capable of viewing all ports. This list
overrides the FCZ port visibility mask. The maximum entries in this
list is 8.

Parameters

This command has one parameter:

hostNodeWwn

The node WWN of the desired control
host, entered in colon-delimited notation
(e.g., 01:02:03:04:05:06:07:08)

Содержание Enterprise Operating System









































































































































































































































































































































Результаты поиска

Содержание Enterprise Operating System

Отзывы:

Похожие инструкции для Enterprise Operating System

Бренды по названию

Популярные бренды

McDATA Enterprise Operating System, Руководство пользователя

Результаты поиска

Содержание Enterprise Operating System

Отзывы:

Похожие инструкции для Enterprise Operating System

Бренды по названию

Популярные бренды