McDATA Enterprise Operating System Скачать руководство пользователя страница 280

Страница: 280 / 328

A-40

Enterprise Operating System Command Line Interface User Manual

Message

Error 250: Invalid counter threshold alert name

Description

The name specified for the alert is not valid.

Action

Specify a counter threshold alert name that has already been created.

Message

Error 251: The threshold alert must be disabled

Description

The counter threshold alert to be modified/deleted is already
enabled.

Action

Disable the threshold alert and then try the command again.

Message

Error 253: Cannot Remove a Member Currently Interacting with the
Fabric

Description

Current members of the fabric must be included in the Fabric Binding
List.

Action

Do not remove active fabric members from the pending Fabric
Binding Membership List.

Message

Error 254: A utilization type must be assigned to this threshold alert

Description

A utilization type must be set before activating this threshold alert.

Action

Add a utilization type and then the threshold alert can be activated.

Message

Error 255: Invalid throughput threshold alert name

Description

The name of the threshold alert is incorrect.

Action

Either the name does not exist, or the new name cannot be used
because it is illegal or a duplicate.

Содержание Enterprise Operating System









































































































































































































































































































































Результаты поиска

Содержание Enterprise Operating System

Отзывы:

Похожие инструкции для Enterprise Operating System

Бренды по названию

Популярные бренды

McDATA Enterprise Operating System, Руководство пользователя

Результаты поиска

Содержание Enterprise Operating System

Отзывы:

Похожие инструкции для Enterprise Operating System

Бренды по названию

Популярные бренды