McDATA Enterprise Operating System Скачать руководство пользователя страница 62

Страница: 62 / 328

2-18

Enterprise Operating System Command Line Interface User Manual

config

Command Example

Root>

config ficonCUPZoning setState 1

config.ficonCUPZoning.show

Syntax

show

Purpose

This command displays the contents of the host control list and the
enabled state of FICON CUP Zoning.

Parameters

This command has no parameters.

Command Example

Root>

config ficonCUPZoning show

Output

The data is displayed as a table that includes the following
information:

Output Example

The output from the config ficonCUPZoning show command
displays as follows:

FICON CUP Zoning State:

Enabled

Host Control List
-----------------------
01:02:03:04:05:06:07:08
09:0A:0B:0C:0D:0E:0F:00

NOTE:

The command

show.ficonCUPZoning

on page 2-152 has functionality

that is identical to this command.

config.ficonMS.setMIHPTO

Synopsis

setMIHPTO timeout

Purpose

This command sets the Ficon MS MIHPTO value in seconds. The
default value is 180 seconds (3 minutes).

FICON CUP
Zoning State

The enabled state of the FICON CUP
Zoning feature

Host Control List List of 0-8 control hosts, displays

“empty” for control host list with no
members.

Содержание Enterprise Operating System









































































































































































































































































































































Результаты поиска

Содержание Enterprise Operating System

Отзывы:

Похожие инструкции для Enterprise Operating System

Бренды по названию

Популярные бренды

McDATA Enterprise Operating System, Руководство пользователя

Результаты поиска

Содержание Enterprise Operating System

Отзывы:

Похожие инструкции для Enterprise Operating System

Бренды по названию

Популярные бренды