McDATA Enterprise Operating System Скачать руководство пользователя страница 308 | Manualshive

Страница: 308 / 328

background image

g-8

Enterprise Operating System Command Line Interface User Manual

Glossary

FRU

See

field-replaceable unit

.

G

G_Port

See

generic port

.

gateway

A multi-homed host used to route network traffic from one network
to another, and to pass network traffic from one protocol to another.

gateway address

(1) In transmission control protocol/Internet protocol (TCP/IP), a
device that connects two systems that use the same or different
protocols. (2) In TCP/IP, the address of a router to which a device
sends frames destined for addresses not on the same physical
network (for example, not on the same Ethernet) as the sender. The
hexadecimal format for the gateway address is XXX.XXX.XXX.XXX.

Gb/s

Acronym for gigabits per second.

generic port

G_Port. Physical interface on a director or switch that can function
either as a fabric port (F_Port) or an expansion port (E_Port),
depending on the port type to which it connects.

GPM

See

G_Port Module

.

G_Port Module

An individual FRU that provides the physical attachment point for
Fibre Channel devices.

Gx_Port

A port configuration allowing a port to transition operationally to
FL_Port as well as to the port operational states described for a
G_Port. Only the Sphereon 4500 Switch supports the configuration of
this port type.

H

hop

(1) Data transfer from one node to another node. (2) Describes the
number of switches that handle a data frame from its origination
point through it’s destination point.

hop count

The number of hops a unit of information traverses in a fabric.

«
...
306
307
308
309
310
...
»

Содержание Enterprise Operating System









































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Enterprise Operating System

Бренд: ShoreTel Страницы: 25

TV708LL/A - NeatWorks For Mac

Бренд: NeatWorks Страницы: 33

BREEZE-MANAGING EXTERNAL BREEZE REPORTS

Бренд: MACROMEDIA Страницы: 18

Web SmartDeviceMonitor Standard

Бренд: Ricoh Страницы: 1

Бренд: Sierra Wireless Страницы: 11

STRM 2008.2R2 - UPGRADING TO STRM 2008.2R2 REV 2

Бренд: Juniper Страницы: 5

Бренд: Bay Networks Страницы: 20

Parallels Desktop 4.0

Бренд: Parallel Страницы: 2

Бренд: ACD Systems Страницы: 232

40D - EOS 40D DSLR

Бренд: Canon Страницы: 50

Бренд: Canon Страницы: 55

ProBook 5320m - Notebook PC

Бренд: HP Страницы: 147

Бренд: HP Страницы: 38

ProBook 4325s - Notebook PC

Бренд: HP Страницы: 160

ProBook 4525s - Notebook PC

Бренд: HP Страницы: 102

Бренд: HP Страницы: 4

Бренд: HP Страницы: 133

Бренд: HP Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды