McDATA Enterprise Operating System Скачать руководство пользователя страница 149

Страница: 149 / 328

CLI Commands

2-105

perf

Output Example

The output from the perf.link command displays as follows.

Port 2

Statistic

Count

-----------

----------

OLS In

753452

OLS Out

351269

Reset In

2953184

Reset Out

1842953

Link Flrs

2953184

Sync Losses

1842953

Sig Losses

35246

Time at 0 Tx Credit

perf.openTrunking.backPressure

Syntax

backPressure backPressureState

Purpose

This command configures the Back Pressure state of the
OpenTrunking configuration.

Reset Out

The number of link resets initiated by this
director or switch.

LIPS In

The number of Loop Initialization Primitives
(LIPS) detected on this switch loop port.

LIPS Out

The number of LIPS generated on this switch
loop port.

Link Flrs

The number of times the port has detected a
link error resulting from an invalid link state
transition or timeout.

Sync Losses

The number of times the port has detected a
loss of synchronization timeout while not in an
offline or LF2 state.

Sig Losses

The number of times the port has detected a
loss of signal while not in an offline or LF2 state.

Time at 0 Tx
Credit

The number of 100 millisecond intervals where
the switch port has zero Tx BB credit.

Содержание Enterprise Operating System









































































































































































































































































































































Результаты поиска

Содержание Enterprise Operating System

Отзывы:

Похожие инструкции для Enterprise Operating System

Бренды по названию

Популярные бренды

McDATA Enterprise Operating System, Руководство пользователя

Результаты поиска

Содержание Enterprise Operating System

Отзывы:

Похожие инструкции для Enterprise Operating System

Бренды по названию

Популярные бренды