McDATA Enterprise Operating System Скачать руководство пользователя страница 265

Страница: 265 / 328

Error Messages

A-25

Message

Error 165: CUP Zoning feature key must be installed

Description

The command is not available without the FICON CUP Zoning
feature key.

Action

Install the FICON CUP zoning feature key.

Message

Error 166: CUP Zoning feature must be enabled

Description

The command cannot be completed with the CUP Zoning feature
enabled.

Action

Enable FICON CUP Zoning.

Message

Error 167: Diagnostics can not be run on inactive port

Description

The port is in the inactive state and diagnostics cannot be run.

Action

The port state must change out of the inactive state.

Message

Error 168: Duplicate member in the list

Description

The member is already in the list.

Action

Duplicate members are not allowed in the list.

Message

Error 169: Cannot enable CNT feature

Description

CNT support is in the wrong state.

Action

The enabled state for CNT support must be changed.

Message

Error 170: Duplicate IP Address range in the switch IP Access
Control List

Description

Duplicate IP address pairs are not allowed in the Access Control List.

Action

This command is redundant, the member already exists in the list.

Содержание Enterprise Operating System









































































































































































































































































































































Результаты поиска

Содержание Enterprise Operating System

Отзывы:

Похожие инструкции для Enterprise Operating System

Бренды по названию

Популярные бренды

McDATA Enterprise Operating System, Руководство пользователя

Результаты поиска

Содержание Enterprise Operating System

Отзывы:

Похожие инструкции для Enterprise Operating System

Бренды по названию

Популярные бренды