CONTROL SYSTEM
i Not Using the SSTs (NGS Tester) at Power Supply
Terminal Inspection
1. Turn the engine switch off.
2. Disconnect the PCM connectors.
3. Measure the voltage between the PCM battery
power terminal connectors and body GND using
an voltmeter.
• If not as specified, repair the related
harnesses and fuses.
Power supply terminal voltage: B+
Off-Vehicle Inspection
1. Disconnect the negative battery cable.
2. Disconnect connector from the idle switch, located
above the accelerator pedal.
3. Inspect for continuity between the idle switch
terminals using an ohmmeter.
• If the idle switch is okay, but PID value or PCM
terminal voltage is out of specification, carry
out the “Circuit Open/Short Inspection”.
• If not as specified, replace the idle switch.
Specification________________________________
Power supply terminal
1
A
Not Using the SSTs (NGS Tester) at Serial
Communication Terminal Inspection
1. Turn the engine switch off.
2. Disconnect the PCM connectors.
3. Verify there is continuity between PCM connector
terminal 3R and DLC KLN terminal.
• If there is no continuity, repair the related
harnesses.
DLC
KLN
l d
e n
COMPONENT SIDE CONNECTOR
(VIEW FROM TERMINAL SIDE)
IDLE SWITCH INSPECTION
On-vehicle Inspection
Note
• Perform the following test only when directed.
1. Verify that the accelerator pedal and idle switch
are properly installed. (See F2-15,
ACCELERATOR PEDAL
DISASSEMBLY/ASSEMBLY)
2. Turn the engine switch on.
3. Monitor the voltage of PCM terminal IT.
Accelerate the accelerator pedal gradually and
hold it at B+. Verify that the voltage of PCM
terminal 2F is within the specification.
• If not as specified, carry out the accelerator
position sensor inspection or idle switch
off-vehicle inspection.
Specification
1.0—1.2 V
Pushing distance (mm {In})
Continuity
Below 1.75 {0.069}
No (OFF)
Above 3.25 {0-127}
Yes (ON)
B
Circuit Open/Short Inspection
1. Inspect for an open or short circuit in the following
wiring harnesses.
• If there is an open or short circuit, repair or
replace wiring harnesses.
Open circuit
• Power circuit (Idle switch connector terminal A and
PCM connector terminal 1T through common
connector)
• GND circuit (Idle switch connector terminal B and
body GND)
Short circuit
• Power circuit (Idle switch connector terminal A and
PCM connector terminal 1T through common
connector to GND)
ACCELERATOR POSITION SENSOR INSPECTION
Note
• Perform the following test only when directed.
1. Verify that the accelerator pedal is properly
installed and accelerator position sensor is
adjusted. (See F2-15, ACCELERATOR PEDAL
DISASSEMBLY/ASSEMBLY.) (See F2-16,
ACCELERATOR POSITION SENSOR
ADJUSTMENT.)
2. If as specified but PID value or PCM terminal
voltage is out of specification, carry out the “Circuit
Open/Short Inspection”.
F2-21
Содержание 626 Station Wagon
