manualshive.com logo in svg

MARUTI SUZUKI Wagon R, Руководство пользователя


Поделиться
Скачать
background image

1G-3 Fuel System: LPG

Manual Shut-off Valve

Rotating the handle clockwise shuts off the main path within the LPG tank valve, and halts the discharge of gas.
This valve has to be open when driving the vehicle normally or when refueling the LPG tank, and it has to be shut in 
unusual circumstances, such as when an accident has occurred or when the vehicle will not be used for an extended 
period of time.

Excess Flow Valve

The excess flow valve is a safety valve that operates 
automatically on the difference between the internal 
pressure of the LPG tank and the pressure at the outlet, 
when gas flow becomes abnormal due to damaged LPG 
fuel pipe, etc.

Shut-Off Valve

The shut-off valve is an electromagnetic isolation valve 
in the fuel path that opens and shuts in response to a 
signal from the LPG control module. For more 
information on valve opening and closing controls, refer 
to “Bi-Fuel LPG System Component Description”: Bi-
Fuel LPG model in Section 1A.
When electric current is supplied to the coil based on a 
signal from the LPG control module, the plunger lifts, 
placing the shut-off valve in an open state.

Fusible Plug

To prevent the LPG tank from burst, when the gas or the 
atmosphere temperature exceeds a specified 
temperature (approx. 120 Deg. C +/- 10 Deg. C), the 
fuse metal melts and the fuel gas in the tank is released 
into the atmosphere.

Pressure Relief Device

To prevent the LPG tank from burst, when the gas 
pressure inside the LPG tank exceeds a specified value 
(approximately 22 bars), the valve opens to relieve the 
gas into atmosphere.

Non-Return Valves

There are two valves in the multifunction valves. Gas 
pressure in the desired direction overcomes the spring 
pressure and opens the shutter to allow the gas to enter 
in the tank. If the direction is opposite, the gas pressure 
pushes the shutter in closed position.?

80% Fill Limiter

It is a spring loaded piston which? is kept in “close” 
position. Gas pressure pushes this piston open? by 
overcoming the spring tension till its stem is set on 
the?cam. When the float reaches 80%,the piston stem 
slides down? the cam and the flow of gas to the tank is 
restricted.?

LPG Fuel Filter Description

AENAR90A1701007

The LPG fuel filter is located downstream from the LPG pressure regulator to remove any impurities (mostly oil) from 
the fuel gas.

LPG Pressure Regulator Description

AENAR90A1701008

LPG pressure regulator is a device to decompress the high pressure gas in the LPG tank to a suitable extent for 
injection by the injector attached beside the battery in the engine compartment.
Gas decompression is performed by a diaphragm in two steps: high-pressure side and low-pressure side. After gas is 
decompressed in first stage, it is further decompressed to a suitable pressure for fuel injection in second stage.
The LPG pressure regulator contains a mechanically operating relief valve, which operates when pressure in the first 
stage exceeds a specified value, venting gas outside.
The pressure sensor that measures the pressure on the high-pressure side, and the shut-off valve that opens and 
shuts in response to a signal from the LPG control module are attached to the fuel gas inlet. For more information on 
valve opening and closing controls, refer to “Bi-Fuel LPG System Component Description”: Bi-Fuel LPG model in 
Section 1A.
While the LPG pressure regulator is in operation, some operating parts may freeze due to adiabatic expansion inside 
the LPG pressure regulator. Engine coolant is circulating through the LPG pressure regulator to prevent freezing.

1. Strainer

11. Solenoid Coil

21. Tank valve Body

2. Float

12. Nut 22. Empty 

Position

3. Suction Pipe

13. Nut Cap

23. Full Position

4. Gasket

14. Gas outlet

24. O-ring

5. Allen Screw

15. Solenoid Assembly

25. Fusible Plug

6. Manual Shut Off Lever

16. Sensor

26. O-ring

7. Sensor

17. Fusible Plug

27. Dust Cap

8. Plunger

18. Gas Inlet

28. Spring

9. Plunger Housing O-ring

19. Open Position

29. Pressure relief valve housing

10. Plunger Housing

20. Closed Position

Содержание Wagon R

















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Wagon R

Dakota Digital Retrotech RTX-68D-CHG Quick Start Manual preview
Retrotech RTX-68D-CHG
Бренд: Dakota Digital Страницы: 4
BMW 01 29 9 416 497 Installation Instructions preview
01 29 9 416 497
Бренд: BMW Страницы: 5
PEUGEOT 407 2010 Manual preview
407 2010
Бренд: PEUGEOT Страницы: 249
BrandMotion FLTW-7690 Installation Instructions preview
FLTW-7690
Бренд: BrandMotion Страницы: 2
Xforce PR-104 User Manual preview
PR-104
Бренд: Xforce Страницы: 11
PMT AS7.M100.001 User Manual preview
AS7.M100.001
Бренд: PMT Страницы: 16
Dodge 2004 JR41 Stratus Sedan Owner'S Manual preview
2004 JR41 Stratus Sedan
Бренд: Dodge Страницы: 273
Carbest 47804 Instruction Manual preview
47804
Бренд: Carbest Страницы: 64
Honda 08F53-T0A-100 Installation Instructions preview
08F53-T0A-100
Бренд: Honda Страницы: 2
Quadratec QuadraTop Adventure Top 1113.00 Series Installation Manual preview
QuadraTop Adventure Top 1113.00 Series
Бренд: Quadratec Страницы: 20
SoundMax SM-DVR77FHD Instruction Manual preview
SM-DVR77FHD
Бренд: SoundMax Страницы: 20
Saab 900 1983 Owner'S Manual preview
900 1983
Бренд: Saab Страницы: 64
Cramaro FARP WORKS CRUSHED CAR Manual preview
FARP WORKS CRUSHED CAR
Бренд: Cramaro Страницы: 8
Thule 202 Installation Instructions preview
202
Бренд: Thule Страницы: 1
Masterack 022553KP Assembly/Installation Instructions preview
022553KP
Бренд: Masterack Страницы: 15
LAS 10637 Operating Instructions Manual preview
10637
Бренд: LAS Страницы: 9
Metra Electronics 99-4503 Installation Instructions Manual preview
99-4503
Бренд: Metra Electronics Страницы: 8
EverFocus EV-RM30 Manual preview
EV-RM30
Бренд: EverFocus Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды