Manitou MLT 845 120 LSU 3-E3 Series, Руководство оператора

Страница: 24 / 128

1-20 1-20
H - TAKING UP AND LAYING DOWN A SUSPENDED LOAD H - TAKING UP AND LAYING DOWN A SUSPENDED LOAD
WARNING: Failure to follow the above instructions may lead the lift WARNING: Failure to follow the above instructions may lead the lift truck to loose stability and over truck to loose stability and over turn. turn.
MUST be used with a lift MUST be used with a lift truck equipped with an operational hydraulic movement cut-out device. truck equipped with an operational hydraulic movement cut-out device.
CONDITIONS OF USE CONDITIONS OF USE
- The length of the sling or the chain shall be as short as possible to limit swinging of the load. - The length of the sling or the chain shall be as short as possible to limit swinging of the load.
- Lift the load vertically along its axis, never by pulling sideways or lengthways. - Lift the load vertically along its axis, never by pulling sideways or lengthways.
HANDLING WITHOUT MOVING THE LIFT TRUCK HANDLING WITHOUT MOVING THE LIFT TRUCK
- - Whether on stabilisers or on tyres, the lateral attitude must not exceed 1 % and the longitudinal attitude must not exceed 5%, the Whether on stabilisers or on tyres, the lateral attitude must not exceed 1 % and the longitudinal attitude must not exceed 5%, the
bubble of the level must be held at “0”. bubble of the level must be held at “0”.
- Ensure that the wind speed is not higher than 10 m/s. - Ensure that the wind speed is not higher than 10 m/s.
- Ensure that there is no one between the load and the lift truck. - Ensure that there is no one between the load and the lift truck.
I - TRAVELLING WITH A SUSPENDED LOAD I - TRAVELLING WITH A SUSPENDED LOAD
- - Before moving, inspect the terrain in order to avoid Before moving, inspect the terrain in order to avoid excessive slopes and cross-fa excessive slopes and cross-fa lls, bumps and potholes, or lls, bumps and potholes, or soft ground. soft ground.
- Ensure that the wind speed is not higher than 10 m/s. - Ensure that the wind speed is not higher than 10 m/s.
- - The lift truck must not travel at more than 0. The lift truck must not travel at more than 0. 4 m/s (1.5 km/h, i. 4 m/s (1.5 km/h, i. e., one quarter walking speed). e., one quarter walking speed).
- - Drive and stop the lift truck gently and smo Drive and stop the lift truck gently and smo othly to minimise swinging of the load. othly to minimise swinging of the load.
- - Carr Carr y the load a few y the load a few centimetres above the ground (max. centimetres above the ground (max. 30 cm) the shortest possible jib length. Do not 30 cm) the shortest possible jib length. Do not exceed the offset exceed the offset
indicated on the load chart. If the load begins to swing excessively, do not hesitate to stop and lower the jib to set down the indicated on the load chart. If the load begins to swing excessively, do not hesitate to stop and lower the jib to set down the
load. load.
- - Before moving the lift truck, check the longitudinal stability alarm device (see: 2 - DESCRIPTION: INSTRUMENTS AND CONTROLS) Before moving the lift truck, check the longitudinal stability alarm device (see: 2 - DESCRIPTION: INSTRUMENTS AND CONTROLS) , ,
only the green LEDs and possibly the yellow LEDs should be lit. only the green LEDs and possibly the yellow LEDs should be lit.
- - During transport, the lift truck operator must be assisted by a person During transport, the lift truck operator must be assisted by a person on the ground (standing a minimum of 3 on the ground (standing a minimum of 3 m from the load), m from the load),
who will limit swinging of the load using a bar or a rope. Ensure that this person is always clearly in view. who will limit swinging of the load using a bar or a rope. Ensure that this person is always clearly in view.
- The lateral attitude must not - The lateral attitude must not exceed 5%, the bubble in the exceed 5%, the bubble in the level must be kept between the level must be kept between the two “MAX.” marks two “MAX.” marks
- The longitudinal attitude must not exceed 15%, with the load facing uphill, and 10%, with the load facing downhill. - The longitudinal attitude must not exceed 15%, with the load facing uphill, and 10%, with the load facing downhill.
- The jib angle must not exceed 45°. - The jib angle must not exceed 45°.
- - If the first red LED of the longitudinal stability alarm device (see: 2 - DESCRIPTION: INSTR If the first red LED of the longitudinal stability alarm device (see: 2 - DESCRIPTION: INSTR UMENTS AND CONTROLS) comes on UMENTS AND CONTROLS) comes on
while travelling, gently bring the lift truck to a stop and stabilise the load. Retract the telescope to reduce the offset of the load. while travelling, gently bring the lift truck to a stop and stabilise the load. Retract the telescope to reduce the offset of the load.
https://www.forkliftpdfmanuals.com/