![background image](http://html1.mh-extra.com/html/magnetek/flex-ex/flex-ex_instruction-manual_3604703043.webp)
Page 42
7.4 Program System Frequency Range (TX & RX)
1) Make sure the programming cable is connected to the system.
2) Press “
→
” button to enter System Frequency Range setting.
3) Press “
↑
” and “
↓
” button to change frequency range.
4) Exit Program System Frequency Range by pressing the “BACK” button
until the cursor is shown next to “FREQ:”.
5) Press “
↑
” and “
↓
” button to scroll through other Flex Mini settings.
7.5 Program System Channel (TX & RX)
1) Make sure the programming cable is connected to the system.
2) Press “
→
” button to enter System Channel setting.
3) Press “
↑
” and “
↓
” button to change system channel as a whole or…
4) Press “
→
” button to go to the digit on the left.
5) Press “
↑
” and “
↓
” button to change numeric value.
6) Press “
→
” button to go to the next digit to the right and repeat step 5
7) Press BACK button to go back to step 3 or 4.
8) Exit Program System Channel by pressing the “BACK” button until the
cursor is shown next to “CHANNEL”.
9) Press “
↑
” and “
↓
” button to scroll through other Flex Mini settings.
7.6 Program RF Power (TX)
1) Make sure the programming cable is connected to the system.
2) Press “
→
” button to enter RF Power setting.
3) Press “
↑
” and “
↓
” button to change RF power (0.01mW ~ 10mW).
4) Exit Program RF Power by pressing the “BACK” button until the cursor is
shown next to “RFpower”.
5) Press “
↑
” and “
↓
” button to scroll through other Flex Mini settings.
7.7 Program Transmitter Inactivity/Sleep Timer (TX)
1) Make sure the programming cable is connected to the system.
2) Press “
→
” button to enter TX Timer setting.
3) Press “
↑
” and “
↓
” button to select ON (sleep timer disabled) or 01M (minute).
4) Press “
→
” button to go to the digit on the far left (tens).
5) Press “
↑
” and “
↓
” button to change numeric value.
6) Press “
→
” button to go to the next digit to the right (units) and repeat step 5.
7) Exit Program Transmitter Inactivity/Sleep Timer by pressing the “BACK”
button until the cursor is shown next to “TX TIMER”.
8) Press “
↑
” and “
↓
” button to scroll through other Flex Mini settings.
7.8 Program Pushbutton Output Relay 1 (PB1/PB2) (RX)
1) Make sure the programming cable is connected to the system.
2) Press “
→
” button to enter Function 1 setting.
3) Press “
↑
” and “
↓
” button to change system channel as a whole or…
4) Press “
→
” button to go to the digit on the far left.
5) Press “
↑
” and “
↓
” button to change numeric value.
6) Press “
→
” button to go to the next digit to the right and repeat step 5.
7) Press BACK button to go back to step 3 or 4.
8) Exit Program System Channel by pressing the “BACK” button until the
cursor is shown next to “PB RLY1”.
9) Press “
↑
” and “
↓
” button to scroll through other Flex Mini settings.
Содержание FLEX EX
