Page 74
9.47 Program PB5 Ramp (RX)
1) Make sure the I-Chip is connected to the programmer.
2) Press “
→
” button to enter PB5 Ramp setting.
3) Press “
↑
” and “
↓
” button to scroll and select “ACC” for acceleration and
“DEC” for deceleration and press “
→
” button to enter.
4) Press “
↑
” and “
↓
” button to change value.
5) Press “BACK” button to go back to step 3.
6) Exit Program PB5 Ramp by pressing the “BACK” button until the cursor is
shown next to “PB5 RAMP”.
7) Press “
↑
” and “
↓
” button to scroll through other Flex EP-H settings.
9.48 Program PB6 Ramp (RX)
1) Make sure the I-Chip is connected to the programmer.
2) Press “
→
” button to enter PB6 Ramp setting.
3) Press “
↑
” and “
↓
” button to scroll and select “ACC” for acceleration and
“DEC” for deceleration and press “
→
” button to enter.
4) Press “
↑
” and “
↓
” button to change value.
5) Press “BACK” button to go back to step 3.
6) Exit Program PB6 Ramp by pressing the “BACK” button until the cursor is
shown next to “PB6 RAMP”.
7) Press “
↑
” and “
↓
” button to scroll through other Flex EP-H settings.
9.49 Program PB7 Ramp (RX)
1) Make sure the I-Chip is connected to the programmer.
2) Press “
→
” button to enter PB7 Ramp setting.
3) Press “
↑
” and “
↓
” button to scroll and select “ACC” for acceleration and
“DEC” for deceleration and press “
→
” button to enter.
4) Press “
↑
” and “
↓
” button to change value.
5) Press “BACK” button to go back to step 3.
6) Exit Program PB7 Ramp by pressing the “BACK” button until the cursor is
shown next to “PB7 RAMP”.
7) Press “
↑
” and “
↓
” button to scroll through other Flex EP-H settings.
9.50 Program PB8 Ramp (RX)
1) Make sure the I-Chip is connected to the programmer.
2) Press “
→
” button to enter PB8 Ramp setting.
3) Press “
↑
” and “
↓
” button to scroll and select “ACC” for acceleration and
“DEC” for deceleration and press “
→
” button to enter.
4) Press “
↑
” and “
↓
” button to change value.
5) Press “BACK” button to go back to step 3.
6) Exit Program PB8 Ramp by pressing the “BACK” button until the cursor is
shown next to “PB8 RAMP”.
7) Press “
↑
” and “
↓
” button to scroll through other Flex EP-H settings.
Содержание FLEX EX
