Page 49
8.14 Program Brake Functions (RX)
1) Press “
→
” button to enter Brake function setting.
2) Press “
↑
” and “
↓
” button to scroll and select.
3) Exit Program Brake Functions by pressing the “BACK” button until
the cursor is shown next to “BRAKE”.
4) Press “
↑
” and “
↓
” button to scroll through other Flex BASE settings.
DEMAG 1
:
When releasing pushbutton from 2
nd
speed up to 1
st
speed, the 1
st
speed
output relay will open for up to 1.0 second and then closes again.
DEMAG 2
:
When pushbutton is pressed down to 2
nd
speed directly from 0 speed, the 1
st
speed output relay will maintain closure for up to 0.4 second before 2
nd
speed
output relay closes. When pushbutton is released from 2
nd
speed up to 0
speed, the 1
st
speed output relay will maintain closure for up to 0.5 second
before going to 0 speed.
DEMAG 3
:
When releasing pushbutton from 2
nd
speed up to 1
st
speed, both 1
st
and 2
nd
speed output relays are opened. Release pushbutton to 0 speed and then
press down to 1
st
speed to reengage the 1
st
speed output relay.
P&H
:
When releasing pushbutton from 2
nd
speed up to 0 speed, the 1
st
speed
output relay will maintain closure for up to 0.1 second before going to 0 speed.
8.15 Program MRX Micro Receiver PB type (RX)
1) Press “
→
” button 2 times to enter PB Type setting.
2) Press “
↑
” and “
↓
” button to scroll and select. PB1~4 setting means the
receiver corresponds to PB1~PB4 on the transmitter. PB5~8 means the
receiver corresponds to PB5~PB8 on the transmitter. PB9~12 means the
receiver corresponds to PB9~PB12 on the transmitter. Inline means the
PB number is counted from top to bottom instead of right to left.
3) Exit Program Micro Receiver PB Type by pressing the “BACK” button
until the cursor is shown next to “MICRO RX”.
4) Press “
↑
” and “
↓
” button to scroll through other Flex BASE settings.
Содержание FLEX EX
