![background image](http://html1.mh-extra.com/html/magnetek/flex-ex/flex-ex_instruction-manual_3604703026.webp)
Page 25
6.25 Program Function Relay 1 (RX)
1) Make sure the I-Chip is connected to the programmer.
2) Press “
→
” button to enter Function Relay 1 setting.
3) Press “
↑
” and “
↓
” button to scroll and select between settings.
4) Exit Program Function Relay 1 by pressing the “BACK” button until
the cursor is shown next to “FUNC RLY1”.
5) Press “
↑
” and “
↓
” button to scroll through other Flex 2JX settings.
Select “LV” for receiver low voltage external warning output.
Select “ID” for receiver ID output (works simultaneously with all joystick motions and
interlocking momentary contacts).
Select “NORMAL” the output relay becomes momentary contact when START button is
pressed.
Select “TOGGLE” the output relay becomes toggled contact when START button is pressed.
Select “TOGGLE&E” the output relay becomes toggled contact affected by the e-stop
command (output relay opens when e-stop button is pressed).
Select “EXT” the output relay works simultaneously with the receiver mains.
Select “S/P” the output relay closes when the green START button is pressed and opens
only when transmitter power is switched off, not e-stop pressed.
Select “TDM A+B” the output relay closes when the 3-stage tandem rotary key switch on
the SW3 slot is rotated to A+B position for dual crane A+B tandem operation.
Select “SW1 1+2… SW5 1+2” the output relay closes when a 3-stage rocker switch, a 3-
stage rotary switch or a 3-stage A/B/A+B button on SW1 ~ SW5 slot is rotated to A+B
position for dual hoist/trolley A+B tandem operation. Only 1 switch or button can be
assigned to each Function relay.
Select “HORN” the output relay closes for up to 3 seconds when the green START button is
pressed after every transmitter power on and then becomes a momentary contact thereafter.
Select “SW1~5 ABC” adds the 3
rd
outputs relay for button or switch A
→
B
→
C selection (see
section 6.16~6.20).
Содержание FLEX EX
