Page 18
6.2 Program Serial Number (TX & RX)
1) Make sure the I-Chip is connected to the programmer.
2) Press “
→
” button to enter Serial Number setting.
3) Press “
↑
” and “
↓
” button to change serial number as a whole or…
4) Press “
→
” button to go to the 1
st
digit on the far left of the serial number.
5) Press “
↑
” and “
↓
” button to change numeric value.
6) Press “
→
” button to go to the next digit to the right and repeat step 5.
7) Press “BACK” button to go back to step 3 or 4.
8) Exit Program Serial Number by pressing the “BACK” button until the cursor
is shown next to “S/N”.
9) Press “
↑
” and “
↓
” button to scroll through other Flex 2JX settings.
When finished, make sure to transfer the newly selected serial number to the receiver.
6.3 Program System Type (TX & RX)
System Type is associated with functions such as tandem operation,
random access operation, multi-receiver operation, etc... Please do not
alter the factory settings unless authorized to do so.
6.4 Program System Frequency Range (TX & RX)
1) Make sure the I-Chip is connected to the programmer.
2) Press “
→
” button to enter System Frequency Range setting.
3) Press “
↑
” and “
↓
” button to change frequency range.
4) Exit Program System Frequency Range by pressing the “BACK” button
until the cursor is shown next to “FREQ:”.
5) Press “
↑
” and “
↓
” button to scroll through other Flex 2JX settings.
When changing the frequency range table in I-Chip make sure the transmitting and receiving
RF boards are also changed accordingly.
6.5 Program System Channel (TX & RX)
1) Make sure the I-Chip is connected to the programmer.
2) Press “
→
” button to enter System Channel setting.
3) Press “
↑
” and “
↓
” button to change system channel as a whole or…
4) Press “
→
” button to go to the digit on the left.
5) Press “
↑
” and “
↓
” button to change numeric value.
6) Press “
→
” button to go to the next digit to the right and repeat step 5
7) Press “BACK” button to go back to step 3 or 4.
8) Exit Program System Channel by pressing the “BACK” button until the
cursor is shown next to “CHANNEL”.
9) Press “
↑
” and “
↓
” button to scroll through other Flex 2JX settings.
When transmitter channel is changed make sure the receiver channel is also set to the
newly selected channel.
Содержание FLEX EX
