Page 46
8.6 Program System Channel (TX & RX)
1) Press “
→
” button to enter System Channel setting.
2) Press “
↑
” and “
↓
” button to change system channel as a whole or…
3) Press “
→
” button to go to the digit on the left.
4) Press “
↑
” and “
↓
” button to change numeric value.
5) Press “
→
” button to go to the next digit to the right and repeat step 4.
6) Press BACK button to go back to step 2 or 3.
7) Exit Program System Channel by pressing the “BACK” button until the
cursor is shown next to “CHANNEL”.
8) Press “
↑
” and “
↓
” button to scroll through other Flex BASE settings.
8.7 Program RF Power (TX)
1) Press “
→
” button to enter RF Power setting.
2) Press “
↑
” and “
↓
” button to change RF power (0.01mW ~ 10mW).
3) Press “
→
” button and then “
↑
” and “
↓
” button to
enable
or
disable
RF
power adjustment via transmitter dipswitch.
4) Exit Program RF Power by pressing the “BACK” button until the cursor is
shown next to “RFpower”.
5) Press “
↑
” and “
↓
” button to scroll through other Flex BASE settings.
8.8 Program Pushbutton Functions (TX)
1) Press “
→
” button to enter Pushbutton Function setting.
2) Press “
↑
” and “
↓
” button to change pushbutton function as a whole or…
3) Press “
→
” button to go to the digit on the left.
4) Press “
↑
” and “
↓
” button to change numeric value.
5) Press “
→
” button to go to the next digit to the right and repeat step 4.
6) Press BACK button to go back to step 2 or 3.
7) Exit Program Pushbutton Functions by pressing the “BACK” button until
the cursor is shown next to “PB FUNC”.
8) Press “
↑
” and “
↓
” button to scroll through other Flex BASE settings.
The transmitter pushbutton function table on Section 12 Part-C illustrates which numeric value
corresponds to which pushbutton function.
8.9 Program Transmitter Inactivity Timer (TX)
1) Press “
→
” button to enter Transmitting Timer setting.
2) Press “
↑
” and “
↓
” button to select “_M” for minutes/seconds or “ON” for
constant on.
3) When “ON” is selected, press “
→
” button and then “
↑
” and “
↓
” button to
select “+START” or “+ANY”.
4) When “_M” is selected, press “
→
” button to go to the digit on the
left and press “
↑
” and “
↓
” button to select value. Press “
→
” button again to
go to the next digit and press “
↑
” and “
↓
” button to select value .
5) Press “
→
” button again to select “M” for minutes or “S” for seconds. Press
“
↑
” and “
↓
” button to select.
6) Press “
→
” button again to select “+START” or “+ANY” selection. Press
“
↑
” and “
↓
” button to select.
7) Exit Program Transmitter Timer by pressing the “BACK” button until the
cursor is shown next to “TX TIMER”.
Содержание FLEX EX
