Page 20
6.9 Program Infrared (IR) Identification Number (TX)
1) Make sure the I-Chip is connected to the programmer.
2) Press “
→
” button to enter Infrared ID setting.
3) Press “
↑
” and “
↓
” button to change IR_ID as a whole or…
4) Press “
→
” button to go to the digit on the far left.
5) Press “
↑
” and “
↓
” button to change numeric value.
6) Press “
→
” button to go to the next digit to the right and repeat step 5.
7) Press BACK button to go back to step 3 or 4.
8) Exit Program Infrared ID by pressing the “BACK” button until the cursor is
shown next to “IR_ID”.
9) Press “
↑
” and “
↓
” button to scroll through other Flex 2JX settings.
Make sure the infrared module on crane is set to same ID code as the transmitter.
Select “000” disables the ID code function hence any types of infrared modules can be used.
6.10 Program IRS Time Out Function (TX)
1) Make sure the I-Chip is connected to the programmer.
2) Press “
→
” button to enter IRS Time Out setting.
3) Press “
↑
” and “
↓
” button to scroll and select between IRS On and IRS Off.
4) Press “
→
” button to go to the digit on the far left.
5) Press “
↑
” and “
↓
” button to change numeric value.
6) Press “
→
” button to go to the next digit to the right and repeat step 5
7) Press BACK button to go back to step 3 or 4.
8) Exit Program IRS Time Out Function by pressing the “BACK” button until
the cursor is shown next to “IRS FUNC”.
9) Press “
↑
” and “
↓
” button to scroll through other Flex 2JX settings.
Select “IRS ON” if infrared START is required after every transmitter timeout.
Select “IRS OFF” if infrared START is not required after every transmitter timeout.
6.11 Program Tilt Function (TX)
1) Make sure the I-Chip is connected to the programmer.
2) Press “
→
” button to enter Tilt setting.
3) Press “
↑
” and “
↓
” button to scroll and select between Off, 1.0S and 0.5S.
4) Exit Program Tilt Function by pressing the “BACK” button until the cursor is
shown next to “TILT”.
5) Press “
↑
” and “
↓
” button to scroll through other Flex 2JX settings.
When TILT function is set to 0.5s (more sensitive) or 1.0s (less sensitive), the receiver mains
are disconnected (opened) when the transmitter is tilted for more than 35~40 degrees. Select
OFF disables the TILT function.
Содержание FLEX EX
