manualshive.com logo in svg

MacDon TR41 S, Руководство оператора, Страница: 52 / 80

Поделиться
Скачать
MacDon TR41 S Скачать руководство пользователя страница 52

 

Commissioning  

 

 

 

50 

If a locking pin  is not available to secure the header at the rear  and/or at the 

front  of  it,  use  the  ratchet  straps  provided  with  the  header  trailer  for  any 

support kit. 

WARNING! 

 

Use edge protector on sharp edges when 

applying ratchet strap. Make sure that the 

strap is not stretched by easily deformable 

parts of the trailer (e.g., brake system 

components). 

 

 

 

 

 

 

7.9 

Commissioning 

1. After attaching the header, make sure that the header rests properly on the 

brackets. Make sure the locking pins are in place (if available). 

2. Check that the lighting equipment is working properly. 

3. Check the tire pressure (see 5.3). 

4. 

Hook up the trailer to the towing vehicle.

 

5. Secure the safety chain/cable, which activates the parking brake if the trailer 

detaches from the towing vehicle accidentally. 

 

WARNING! 

 

The breakaway chain/wire Nr.1 shall be threaded 

through the tab Nr.2 and connected to the towing 

vehicle. The other end of the chain/wire shall be 

connected to the split ring Nr.3 on the park brake lever. 

 

WARNING! 

 

Improperly supported and secured headers 

can move, fall, and cause an accident during 

shipping. 

Содержание TR41 S

















































































Отзывы:

Нет отзывов