manualshive.com logo in svg

MacDon TR41 S, Руководство оператора, Страница: 20 / 80

Поделиться
Скачать
MacDon TR41 S Скачать руководство пользователя страница 20

 

Safety regulations  

 

 

 

18 

WARNING! 

 

Always follow the traffic rules and 

restrictions which are in force in the 

respective country (e.g., size and 

speed restrictions)!

 

 

4.8 

Safety and accident prevention regulations during maintenance. 

-  Repair, maintenance, cleaning work and the elimination of malfunction should 

only  ever  be  preformed  once  the  engine  of  the  towing  machine  has  been 

switched off. 

– Remove the ignition key. 

-  Make  sure  that  the  parking  brake  is  applied,  and  the  wheel  chocks  are 

correctly positioned when the trailer is not connected to the towing vehicle. 

-  Check all nuts and bolts  for their  tightness regularly and tighten if necessary. 

The  recommended  tightening  torques  for  the  fasteners  can  be  found  in  this 

operating instruction or in a separate description of the respective component. 

-  Ensure  that  the  header  trailer  is  secured  against  falling  with  appropriate 

support elements, when preforming maintenance work on the raised machine. 

-  Ensure  that  the  power  supply  of  the  trailer  is  disconnected  when  performing 

electrical welding work on the vehicle and connected devices. Disconnect the 

power  supply  via  the  battery  main  switch  or  remove  the  cable  lugs  from  the 

battery poles. 

The  spare  parts  must  comply  with  the  technical  specifications  of  the 

manufacturer,  as  a  minimum.  The  use  of  other  parts  may  invalidate  any 

liability for the resulting consequences.

 

 

 

 

 

 

 

 

 

 

 

Содержание TR41 S

















































































Отзывы:

Нет отзывов