manualshive.com logo in svg

MacDon TR41 S, Руководство оператора, Страница: 16 / 80

Поделиться
Скачать
MacDon TR41 S Скачать руководство пользователя страница 16

 

Safety regulations  

 

 

 

14 

WARNING! 

 

Before commissioning, read the operating instructions and 

learn how to operate, inspect and maintain the machine 

safely. Do not allow anyone to operate the machine without 

following the instructions! 

 

Keep  the  machine  in  good  working  condition.  Improper  or  unauthorized 

modifications may impair the function, service life and safety of the machine. 

 

4.2 

Personnel qualification and training 

The machine may only be used, serviced and repaired by those persons who 

are  familiar  with  it  and  have been  informed of  the  dangers  which  it  presents. 

The owner must clearly establish the areas of responsibility and monitoring of 

personnel.  Personnel  lacking  any  requisite  knowledge  must  be  trained  and 

instructed.  The  owner  must  ensure  that  the  personnel  have  read  and 

understood  the  specifications  of  the  operating  instructions  entirely.  Repair 

work  not  described  in these  operating  instructions may only be  performed by 

an authorized specialist workshop. 

 

4.3 

The risks resulting from non-compliance with safety warnings 

Failure to comply with the safety instructions can result in hazards for persons, 

the  environment  and  the  machine  itself.  Failure  to  comply  with  the  safety 

instructions can result in loss of all liability cover. 

Non-compliance can result in the following hazards: 

- Hazards to persons through unsecured working areas 

- The failure of important machine functions 

- The failure of the prescribed methods of maintenance and repair 

- The endangerment of persons from mechanical and chemical influences 

 

 

 

 

 

Содержание TR41 S

















































































Отзывы:

Нет отзывов