manualshive.com logo in svg

MacDon TR41 S, Руководство оператора, Страница: 17 / 80

Поделиться
Скачать
MacDon TR41 S Скачать руководство пользователя страница 17

 

Safety regulations 

 

 

 

15 

4.4 

Safety-conscious work 

Follow  the  warnings  in  this  manual,  all  applicable  accident  prevention  regulations 

and all internal work, operation and safety regulations. Compliance with the health, 

safety and accident prevention regulations of the relevant professional associations 

is  mandatory.  Follow  the  vehicle  manufacturer's  safety  warnings.  When  using  on 

the  road,  observe  the  relevant  regulations  (e.g.,  StVZO  and  StVO  in  Germany). 

Prepare  for  any  emergency.  Keep  fire  extinguishers  and  first  aid  kits  nearby. 

Display the emergency number for medical and fire services on each telephone. 

 

4.5 

Safety precautions before operation 

-  In addition to the information in these operating instructions, comply with all 

the generally valid safety and accident prevention regulations. 

-  Familiarize yourself with the road traffic regulations in your county. 

-  Familiarize yourself with the accident prevention regulations for connection to 

the towing vehicle. 

-  Check the general condition of the header trailer. 

-  Check the tightness of the fasteners (bolts, nuts, etc.) at regular intervals and 

tighten if necessary. 

-  Check the tire pressure at regular intervals. 

-  Make sure that the mirrors on the towing vehicle allow both sides of the towed 

transport vehicle to be seen. 

-  Make sure that the lights of the trailer are working properly. 

-  Make sure that no one is working or presented on the trailer and the towing 

vehicle. 

-  Make sure that nobody is in the working area of the trailer and the towing 

vehicle. Before starting, warn people nearby by switching on the audible 

warning device of the towing vehicle several times. 

-  Check the trailer and the towing vehicle for foreign objects that could interfere 

with maneuvering. 

-  Operating personnel should wear tight-fitting clothing. Avoid wearing any loose 

clothing, hair and jewelry. 

 

Содержание TR41 S

















































































Отзывы:

Нет отзывов