MacDon R116 Скачать руководство пользователя страница 161 | Manualshive

Страница: 161 / 234

background image

214713

153

Revision A

Chapter 8:

Transporting the Disc Mower

You can transport the disc mower using a tractor in either field mode or Road Friendly Transport

™

mode.

•

To prepare a disc mower for towing with a tractor in field mode without using the Road Friendly Transport

™

option, refer to

8.1 Preparing Disc Mower for Transport, page 153

•

To prepare a disc mower for towing with a tractor using the Road Friendly Transport

™

option, refer to

Converting from Field to Transport Mode (With Road Friendly Transport

CAUTION

•

Obey all highway traffic regulations in your area when transporting on public roads. Use flashing amber
lights unless prohibited by law.

•

Be aware of roadside obstructions, oncoming traffic, and bridges.

•

Travel at safe speeds to ensure complete machine control and stability at all times. Do NOT exceed
32 km/h (20 mph). Reduce speed for corners and slippery conditions.

•

Use tractor lights and disc mower flashing amber and red taillights when transporting on roads in order
to provide adequate warning to operators of other vehicles.

•

Do NOT transport the disc mower on a road or highway at night or in reduced visibility conditions such
as rain or fog.

•

Ensure that hitch on transporting vehicle is capable of handling a 907 kg (2000 lb.) static vertical load.

•

Do NOT tow with any highway-capable vehicle. Use only an agricultural tractor with a sufficient weight
such that the fully loaded implement weighs no more than 1.5 times the weight of the tractor.

8.1

Preparing Disc Mower for Transport

Follow these instructions to prepare the disc mower for transport without deploying the optional Road Friendly
Transport

™

system.

DANGER

To avoid bodily injury or death from unexpected startup of machine, always stop engine and remove key
from ignition before leaving operator

’

s seat for any reason.

WARNING

Do NOT tow unless the hitch swing cylinder is fully charged. If hitch swing cylinder is not fully charged,
loss of control, injury, or death could result.

«
...
159
160
161
162
163
...
»

Содержание R116











































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для R116

MicroVersaTrip Plus

Бренд: GE Страницы: 20

Бренд: GE Страницы: 252

Бренд: Balanced Body Страницы: 12

Бренд: Eagle Pro Страницы: 6

Бренд: GE Страницы: 10

Бренд: YSI Страницы: 70

Бренд: jcb Страницы: 41

Бренд: Danfoss Страницы: 106

Бренд: IBEX Страницы: 4

Бренд: Kamikaze Страницы: 112

Бренд: KAM Страницы: 2

Бренд: Harken Страницы: 4

MIAMI J ADVANCED

Бренд: Össur Страницы: 35

Бренд: Össur Страницы: 38

Бренд: Össur Страницы: 8

Бренд: Össur Страницы: 72

Бренд: Össur Страницы: 76

Miami Lumbar Posteo

Бренд: Össur Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды