MacDon R116 Скачать руководство пользователя страница 137 | Manualshive

Страница: 137 / 234

background image

214713

129

Revision A

7.3

Checking Conditioner Drive Belt

DANGER

To avoid bodily injury or death from unexpected startup of machine, always stop engine and remove key
from ignition before leaving operator

’

s seat for any reason.

NOTE:

If no conditioner is installed, proceed to

7.4 Checking Cutting Angle, page 130

.

1011422

B

A

C

D

E

Figure 7.4: Conditioner Drive Belt

1.

Open left driveshield. For instructions, refer to

Opening Driveshields, page 119

.

2.

Check that belt (A) is properly positioned on the pulleys
and tensioned. Overall spring length (B) should be
365 mm (14-3/8 in.). If adjustment is required, refer to

7.3.1 Adjusting Conditioner Drive Belt, page 129

.

3.

Check that adjuster nuts (C) are tight.

4.

Check that the spring is hooked at the correct location:

•

Hole (D) for roll conditioner

•

Hole (E) for finger conditioner

5.

Close driveshield. For instructions, refer to

Driveshields, page 126

.

7.3.1

Adjusting Conditioner Drive Belt

DANGER

To avoid bodily injury or death from unexpected startup of machine, always stop engine and remove key
from ignition before leaving operator

’

s seat for any reason.

1.

Shut down the engine, and remove the key from the ignition.

2.

Open the left driveshield. For instructions, refer to

6.1 Opening Driveshields, page 119

1018589

B

A

C

D

E

F

Figure 7.5: Conditioner Drive Belt

3.

Check that the spring is hooked at the correct location:

•

Hole (C) for roll conditioner

•

Hole (D) for finger conditioner

4.

Turn jam nut (F) counterclockwise to unlock
tension adjustment.

5.

Turn adjuster nut (E) clockwise to increase spring
length (tension). To decrease spring length (relax), turn
adjuster nut (E) counterclockwise.

6.

Set overall spring length (B) to 365 mm (14-3/8 in.).

7.

Close driveshield. Refer to

6.3 Closing Driveshields,

PERFORMING PREDELIVERY CHECKS

«
...
135
136
137
138
139
...
»

Содержание R116











































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для R116

Бренд: VeEX Страницы: 2

Бренд: JB-Lighting Страницы: 48

Бренд: Raymarine Страницы: 90

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: ODA Страницы: 103

BELMONT 2001039

Бренд: Backyard Discovery Страницы: 50

Бренд: Backyard Discovery Страницы: 45

Бренд: Backyard Discovery Страницы: 70

Бренд: BACtrack Страницы: 16

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 20

Бренд: ICP DAS USA Страницы: 45

Бренд: Landoll Страницы: 70

Бренд: Landice Страницы: 19

Бренд: Landice Страницы: 7

Бренд: Saadat Страницы: 61

Бренд: Saadat Страницы: 22

Бренд: Xtool Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды