MacDon R116 Скачать руководство пользователя страница 159 | Manualshive

Страница: 159 / 234

background image

214713

151

Revision A

7.18

Running up the Header

DANGER

•

Keep everyone several hundred feet away from your operation. Ensure bystanders are never in line with
the front or rear of the machine. Stones and other foreign objects can be ejected from either end
with force.

•

Take extreme care to avoid injury from thrown objects. Do NOT, under any circumstances, operate the
disc mower when other people are nearby.

•

Check cutterbar area carefully for loose parts and hardware on the cutterbar. These objects can be
ejected with considerable force when the machine is started, and may result in serious injury or
machine damage.

•

Cutterbar curtains reduce the potential for thrown objects. Always keep these curtains down when
operating the disc mower. Replace the curtains if they become worn or damaged.

DANGER

Before investigating an unusual sound or attempting to correct a problem, shut off engine, engage
parking brake, and remove key.

CAUTION

Never start or move the machine until you are sure all bystanders have cleared the area.

NOTE:

Higher engine rpm may be required to engage the header. Do

NOT

exceed 1800 rpm.

1.

Start the tractor.

2.

Set header 152

–

305 mm (6

–

12 in.) above the ground and adjust center-link to mid-position.

3.

Run the machine slowly for 5 minutes, watching, and listening

FROM THE OPERATOR

’

S SEAT

for binding or

interfering parts.

4.

Run the machine at operating speed for 15 minutes. Listen for any unusual sounds or abnormal vibration.

5.

Perform the run-up check as listed on the Predelivery Checklist (yellow sheet inside the back cover of this
instruction) to ensure the machine is field-ready.

6.

Retain the Checklist and (if desired), retain this instruction for future reference.

PERFORMING PREDELIVERY CHECKS

«
...
157
158
159
160
161
...
»

Содержание R116











































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для R116

Бренд: GE Страницы: 138

Бренд: 1010music Страницы: 2

Бренд: 1010music Страницы: 4

Бренд: NEILPRYDE Страницы: 53

Бренд: JAC Страницы: 103

Бренд: 3Disc Страницы: 12

Бренд: CAMPAGNOLA Страницы: 4

Бренд: Eastern Jungle Gym Страницы: 27

MET ONE 3400 Series

Бренд: Hach Страницы: 48

Бренд: IFM Страницы: 175

Бренд: IFM Страницы: 5

Бренд: Land Pride Страницы: 38

Бренд: Keithley Страницы: 79

Бренд: Kayakpro Страницы: 17

Бренд: Yoshitake Страницы: 11

Бренд: M-Audio Страницы: 25

Бренд: Gardena Страницы: 33

Бренд: Backyard Adventures Playcenter Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды