MacDon R116 Скачать руководство пользователя страница 145

Страница: 145 / 234

214713

137

Revision A

Perform this procedure on both upper and lower gearboxes:

1026366

Figure 7.16: Swivel Gearbox

Adjust the height and angle of the hitch until the upper
and lower gearboxes are parallel to the ground.

NOTE:

The oil should be checked when the gearboxes are
parallel to the ground.

Turn off engine and remove key.

Clean area around check plug (A).

Remove check plug using a 13 mm socket.

Check lubricant level and ensure lubricant is visible or
slightly draining form the port.

If necessary, add gear oil to gearboxes through
breather/filler plug (B). Refer to

11.5 Recommended

Lubricants, page 207

Reinstall check plug (A) and breather/filler plug (B)
and tighten.

PERFORMING PREDELIVERY CHECKS

Содержание R116











































































































































































































































Результаты поиска

Содержание R116

Отзывы:

Похожие инструкции для R116

Бренды по названию

Популярные бренды

MacDon R116, Инструкции по разгрузке и сборке

Результаты поиска

Содержание R116

Отзывы:

Похожие инструкции для R116

Бренды по названию

Популярные бренды