MacDon R116 Скачать руководство пользователя страница 70

Страница: 70 / 234

214713

Revision A

1013890

Figure 4.13: Hitch Packing

Cut banding (A) securing wood supports, then
remove supports (B).

Remove the two bolts (C) securing wood support to
hitch pin. Discard bolts.

1012287

Figure 4.14: Lifting Hitch

Place sling (A) around the hitch frame. Adjust sling
position until hitch is balanced when lifting.

•

R113

: Approximately 270 cm (106 in.) from the edge

of the tractor end of the hitch (B)

•

R116

: Approximately 350 cm (138 in.) from the edge

of the tractor end of the hitch (B)

Raise the hitch approximately 610 mm (24 in.) off
the ground.

1013891

Figure 4.15: Hitch Packing

NOTE:

Pin (C) is heavy; support it appropriately before
removing bolt (A).

Support pin (C), remove bolt (A) and wood block (B)
from top of pin, and then remove pin (C).

ASSEMBLING THE DISC MOWER (FACTORY-INSTALLED TRANSPORT)

Содержание R116











































































































































































































































Результаты поиска

Содержание R116

Отзывы:

Похожие инструкции для R116

Бренды по названию

Популярные бренды

MacDon R116, Инструкции по разгрузке и сборке

Результаты поиска

Содержание R116

Отзывы:

Похожие инструкции для R116

Бренды по названию

Популярные бренды