MacDon R116 Скачать руководство пользователя страница 164

Страница: 164 / 234

214713

156

Revision A

8.2

Transporting with a Tractor

If towing endwise with the optional Road Friendly Transport

™

system, refer to

8.6.1 Converting from Field to

Transport Mode (With Road Friendly Transport

™

), page 160

Before transporting the disc mower with a tractor, ensure the machine is prepared for transport. Refer to

8.1

Preparing Disc Mower for Transport, page 153

Ensure hitch safety chain is properly connected to the tractor. Provide only enough slack in chain to permit
turning.

1026353

Figure 8.6: Jack in Storage Position

Move jack (A) to storage position on side of hitch, and
secure with pin (B).

NOTE:

If unit is equipped with a two-point hitch, rotate the
stand to the storage position.

Ensure the hydraulic hoses are securely stored on
the hitch.

NOTE:

The primary driveline and hydraulic hoses do not need
to be attached to the tractor for towing.

Ensure the hitch swing lock-out and the two lift-cylinder
lock-out valves are closed (handle 90 degree to
the hose).

NOTE:

Keep the slow moving vehicle (SMV) sign, reflectors,
and lights clean and visible at rear of disc mower.

Ensure tires are properly inflated.

IMPORTANT:

NOT

exceed 32 km/h (20 mph).

TRANSPORTING THE DISC MOWER

Содержание R116











































































































































































































































Результаты поиска

Содержание R116

Отзывы:

Похожие инструкции для R116

Бренды по названию

Популярные бренды

MacDon R116, Инструкции по разгрузке и сборке

Результаты поиска

Содержание R116

Отзывы:

Похожие инструкции для R116

Бренды по названию

Популярные бренды