MacDon R116 Скачать руководство пользователя страница 17

Страница: 17 / 234

214713

Revision A

Chapter 3:

Assembling the Disc Mower (With or Without

the Dealer-Installed Transport)

Perform the following procedures in the order provided to assemble the disc mower without the transport system, or
when the Road Friendly Transport

™

will be installed by the Dealer.

To assemble a disc mower with the factory-installed transport, refer to

4 Assembling the Disc Mower (Factory-

Installed Transport), page 57

3.1

Repositioning Center-Link Top Anchor

Perform this procedure to reposition the center-link top anchor into working position.

1011354

Figure 3.1: Carrier

Place forklift forks (B) under top beam and lift carrier
frame (A) slightly until pin at base of center-link anchor
is loose. Use a piece of wood (C) to protect paint
on frame.

1011500

Figure 3.2: Float Spring

Loosen jam nut (A) and fully loosen float spring bolt (B).
Repeat on the opposite side.

Содержание R116











































































































































































































































Результаты поиска

Содержание R116

Отзывы:

Похожие инструкции для R116

Бренды по названию

Популярные бренды

MacDon R116, Инструкции по разгрузке и сборке

Результаты поиска

Содержание R116

Отзывы:

Похожие инструкции для R116

Бренды по названию

Популярные бренды