manualshive.com logo in svg

Lochinvar EcoForce EF100, Инструкции по установке, пусконаладке, эксплуатации и техническому обслуживанию

"Lochinvar EcoForce EF100" - эффективный и надежный котел для отопления дома. У нас вы можете скачать бесплатно руководство по установке, пуско-наладке, эксплуатации и обслуживанию товара. Просто загрузите руководство с manualshive.com и наслаждайтесь работой вашего котла без проблем.

Поделиться
Скачать
background image

 

 

111 

 

LPG FUEL 

 

 

It is strongly recommended that, on LPG installations, gas detection equipment is fitted.  This equipment should be 
positioned near the appliance and at low level.  It is also important that the space housing the appliance is 

adequately ventilated at high and low level.  This appliance must not be located below ground e.g. in a cellar 

 

 

R

ELATED 

D

OCUMENTS

 

In addition to those documents listed in Section 4.1: RELATED DOCUMENTS within the main body of the installer’s guide the gas installation 
should also comply with the guidance offered in the following documents. 

BS 5482-1: 2005 

Code of practice for domestic butane and propane gas burning installations. 
Part 1: Installations at permanent dwellings, residential park homes and commercial premises, 

with 

installation pipework sizes not exceeding dn25 for steel and dn28 for corrugated stainless steel or copper. 

The operation of the E

CO

F

ORCE

™ range on LPG-Butane/Propane (3

rd

 Family) 3P is similar to that on Natural Gas (2

nd

 Family) 2H and the 

design and installation details described in the main body of the installer’s guide should be followed. 

 

C

ONVERSION 

A

ND 

C

OMMISSIONING 

P

ROCEDURE

 

This process must be carried out in the order stated when the water heater is switched on for the first time.  Failure to follow the following 

procedure may lead to non-warrantable damage to the water heater. 
Before starting the conversion procedure the control parameter for gas type should be adjusted as below: 
P4 BD 

Gas type (0=standard, 1=propane , 2=B/P) (display D8) 

This parameter is set 0 for the common used gas types such as natural gas G20 or G25. 
By setting this parameter 1 for propane G31, fan speed is reduced. 
Set this parameter 2 for B/P. G30

 

0 = 

standard gas (e.g: natural gas) 

1 = 

propane 

2 = 

B/P 

 

For each setting, the relevant Soft start settings are automatically adjusted, depending on its main setting P4BE, see section 15.4. 

 

 

If this is a gas conversion, paste the corresponding sticker at the appropriate position in the Water heater and 
mark the square for the used gas type. Also mark the square, indicating that the correct value has been set for 
parameter P4BD. 

 

 
Due to the design of the water heater, the conversion to LPG-Propane requires adjustment of the gas valve only (see 

24.2.1

).  The sequence 

is as follows: 
 

1.

 

Ensure that the gas inlet appliance isolating valve, provided by the installer, is in the “off” position. 

2.

 

Press the power rocker switch, positioned on the front of the appliance next to the control thermostat, to bring the equipment on. 

3.

 

Depress the recessed button located below the computer interface port to place the water heater into service mode. 

4.

 

The combustion fan should ramp up to full speed to purge the combustion chamber and then drop back to half rate in order to light.  
The spark generator should create a spark, visible through the burner sight glass.  As the gas inlet appliance isolating valve is closed, 
the controls should go to a flame failure condition after four ignition attempts. 

5.

 

Isolate the electrical supply to the appliance.  Turn screw 2 clockwise until the screw stops then turn anti-clockwise through two full 
turns. 

6.

 

Turn on the main power to the water heater, press the reset button and place the unit into service mode. 

7.

 

If the water heater does not fire after three ignition attempts, turn screw 2 through a further half turn anti-clockwise. 

8.

 

Turn the set point dial fully clockwise, this should ramp the fan up to its maximum speed. 

9.

 

Adjust screw 2 to give a CO

2

 output of 9.8% (± 0.3%).  Turning the screw clockwise will reduce the CO

2

 level, turning anti-clockwise 

will increase the CO

2

 level.  On the EF150 and EF180, this adjustment should be made to the right hand gas valve only. 

10.

 

Turn the set point dial fully anti-clockwise, this should ramp the fan down to its minimum speed. 

PROPANE

PROPAN

PROPANO

PROPAAN

BUTANE/PROPANE

BUTAN/PROPAN

BUTANO/PROPANO

BUTAAN/PROPAAN

P4BD = 1

P4BD = 2

G31 P

G30/G31 B/P

Содержание EcoForce EF100

























































































































Отзывы:

Нет отзывов

Похожие инструкции для EcoForce EF100

Water Well D55 User Manual preview
D55
Бренд: Water Well Страницы: 5
umbra pompe SAL 35 Operating Instructions Manual preview
SAL 35
Бренд: umbra pompe Страницы: 16
A.O. Smith 305 Specification Sheet preview
305
Бренд: A.O. Smith Страницы: 2
A.O. Smith BURKAY 102 Series Instruction Manual preview
BURKAY 102 Series
Бренд: A.O. Smith Страницы: 24
Samson KL Series Directions For Use Manual preview
KL Series
Бренд: Samson Страницы: 8
Kambrook KRH200 Manual preview
KRH200
Бренд: Kambrook Страницы: 6
Taurus Alpatec AGADIR 1500 User Manual preview
AGADIR 1500
Бренд: Taurus Alpatec Страницы: 52
Underhill GULP PRO Care And Maintenance Instructions preview
GULP PRO
Бренд: Underhill Страницы: 2
Bionaire BOF3001-CN Instruction Leaflet preview
BOF3001-CN
Бренд: Bionaire Страницы: 8
Goldair GCT200 Operating Instructions Manual preview
GCT200
Бренд: Goldair Страницы: 6
PHP PHP-52W Manual preview
PHP-52W
Бренд: PHP Страницы: 31
Cadet CE163T Owner'S Manual preview
CE163T
Бренд: Cadet Страницы: 16
EQUATION 3276000272311 Assembly, Use, Maintenance Manual preview
3276000272311
Бренд: EQUATION Страницы: 12
Chronomite INSTANT-FLOW MICRO MIX Series Get Started preview
INSTANT-FLOW MICRO MIX Series
Бренд: Chronomite Страницы: 2
salmson SCX Installation And Starting Instructions preview
SCX
Бренд: salmson Страницы: 20
RainScapes Rain Barrel Assembly preview
Rain Barrel
Бренд: RainScapes Страницы: 2
Redring WS7-EcoT Installation Instructions Manual preview
WS7-EcoT
Бренд: Redring Страницы: 4
LAGO CLTL100 User Manual preview
CLTL100
Бренд: LAGO Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды