Lochinvar EcoForce EF100 Скачать руководство пользователя | Manualshive

Страница: 58 / 120

background image

58

S

ETPOINTS

The following show how to programme the hot water set points

Heating set point normal/day time: (parameter P4 AA = 1/2)

D H W s e t p o i n t

6 0 ° C

This is the water temperature set point that is active during the

programmed DHW periods (parameter P4 AA = 1/2)

DHW set point reduction: (parameter P4 AA = 1/2)

D H W R e d u c e

1 0 ° C

The reduction of the normal/day time set point. This reduction is used
outside the programmed CH periods.

DHW setpoint reduction: (parameter P4 AA = 2 and
P5 DJ&DK =1)

H e a t i n g s e t p o i n t

7 5 ° C

This parameter is the local setpoint of the water heater and is regulated
on sensor S1 (parameter P4 AA = 2, P5 DJ = 1 and P5 DK =1 ).

NOTICE:
The max. actual DHW temperature will never exceed the

value set at Heating Setpoint Regardless the set DHW
setpoint
If higher DHW setpoint are needed the Heating Setpoint

has to be set higher also.

12.9.1

Set points display

S

ETTING

T

HE

T

IMER

P

ROGRAMS

Two different programmes can be set within the water heater, DHW programme and Pasteurisation programme
Three programmed periods each day can be set (period 1, 2 and 3) During this time the water heater will operate at the normal DHW set point.

Outside these time periods the water heater will operate at the reduced temperature set point. When no time is programmed for a period the
period will not be used.

Operating screen:

W A T R H T R : b o i l e r o f f

> > > : 1 2 3 . 4 ° C ( 1 2 3 . 4 ° C )

Press [MENU]

Select "Timer" using [◄] & [►] and press [ENTER]

Main menu screen:

M a i n M e n u

T i m e r

Press [ENTER]

Setting program times:

P r o g r a m C H

M o n 1 0 6 : 0 0 - 2 3 : 0 0

Press [

◄

] for next SCREEN

> > > Continue on next page HOT WATER program < < <

12.10.1

Start programme display screen

«
...
56
57
58
59
60
...
»

Содержание EcoForce EF100

























































































































Отзывы:

Нет отзывов

Похожие инструкции для EcoForce EF100

Бренд: Gabarron Страницы: 8

aroSTOR VWL B 200/5 UK

Бренд: Vaillant Страницы: 24

Бренд: Vaillant Страницы: 20

Бренд: Vaillant Страницы: 24

Бренд: Orbegozo Страницы: 85

Бренд: Naked Страницы: 12

Бренд: Pattfield Ergo Tools Страницы: 52

Бренд: Vectra Fitness Страницы: 28

Бренд: Oase Страницы: 16

Бренд: Noctua Страницы: 2

Бренд: Launtop Страницы: 22

Бренд: DROPSA Страницы: 16

Larius GHIBLI 10:1

Бренд: Samoa Страницы: 28

Бренд: L.B. White Страницы: 96

Бренд: YAMADA Страницы: 16

Бренд: Enapter Страницы: 30

Бренд: Paramount Fitness Страницы: 15

ISMATEC REGLO-Z Digital

Бренд: Idex Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды