Lochinvar EcoForce EF100 Скачать руководство пользователя | Manualshive

Страница: 66 / 120

background image

66

S

ETTING

T

HE

U

SER

L

OCK

The following graphs describe how to activate the user lock of the display. The standard factory setting for this function is “OFF”.

The "USER LOCK" menu.
In this menu the water heater can be locked for (end-)users.
0 = UNLOCKED

1 = LOCKED
When the water heater is unlocked, the user can enter the
MENU by pressing the menu button and all screens
will show up.
When the water heater is locked, the user has to push the:

[MENU] button together with the [▼] button for 5 seconds.
to access all menu screens.
This function is to prevent accidental changes!
NOTICE: The PARAMETER screen is always accessible.

Operating screen:

H E A T I N G : S T A N D - B Y

> > > : 1 2 3 . 4 ° C ( 1 2 3 . 4 ° C )

Press [MENU]

Select "User lock" using [◄] & [►] and press [ENTER]

User lock screen:

S e t U s e r l o c k = 0

0

The "0" is now blinking/selected and can be changed.
Use [▲] & [▼] to change the value.
0 = User lock function OFF

1 = User lock function ON
Press [ENTER] for the confirmation screen after the selection has been
made.

Confirmation screen:

A r e y o u s u r e

< C a n c e l ; > C o n f i r m

Press [◄] to cancel the changes (the unit will reset and the display returns
to the operating screen).
Press [►] to confirm the changes. The changed value will be blinking for a

few seconds. After this, the display returns to the operating screen.

NOTICE:

Using the [MENU] button during the User lock display will reset the water
heater and the water heater will return to the operating screen. Changes will

be rejected in this case.

12.16.1

Setting the user lock

«
...
64
65
66
67
68
...
»

Содержание EcoForce EF100

























































































































Отзывы:

Нет отзывов

Похожие инструкции для EcoForce EF100

Бренд: Calpeda Страницы: 80

Бренд: vacuubrand Страницы: 44

Бренд: Takagi Страницы: 27

DURA-Power DRE-52

Бренд: A.O. Smith Страницы: 26

DURA-Power DRE-52

Бренд: A.O. Smith Страницы: 20

Бренд: Cadet Страницы: 9

Infinite Energy2 IW1000

Бренд: RBI Страницы: 156

Бренд: Frico Страницы: 28

Бренд: Lochinvar Страницы: 16

Бренд: Wilo Страницы: 80

StreetHeat SR-28

Бренд: INTEGRATED PAVING CONCEPTS Страницы: 21

Бренд: Toyostove Страницы: 17

Бренд: German pool Страницы: 17

Бренд: A.O. Smith Страницы: 32

Бренд: Pro-Elec Страницы: 4

Бренд: Rinnai Страницы: 32

Бренд: O-SO Pure Страницы: 16

Бренд: Bock Water heaters Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды