Lister Petter TS/TR1, Руководство по ремонту

Страница: 54 / 100

TS, TR, TX engines workshop manual 54
T SERIES ENGINES WORKSHOP MANUAL
59
Figure 4.1.3 Cold Start
3.Replace the plunger and inject the oil just before
starting the engine.
CAUTION
The device must not be used more than three
times in succession during the same attempt to
start the engine.
4.2 HAND STARTING
Before attempting to start the engine refer to
"Starting Handle Precautions".
1.Select the excess fuel position by turning the
engine control lever anti-clockwise to the ‘STOP’
position and releasing it.
Figure 4.2.1 The Engine Control
2.If a variable speed control lever is fitted move it
to the fast position.
3.Move the decompressor lever towards the
flywheel.
Figure 4.2.3 Decompressor Lever
A - TS/TR; B - TX
4.If the ambient temperature is below -10°C
(14°F) refer to "Cold Starting Aid - TS/TR".
5a. If using a non-limited kick-back handle:
Insert the correct handle, refer to 'A' in 'Figure
4.1.1', into the starting housing.
Figure 4.2.3 Starting Handle Housing
Slowly rotate the handle in the direction of
cranking until it fully engages.
5b. If using a limited kick-back handle:
Swivel the starting handle housing cover (A) to
one side and insert the correct handle, refer to 'B'
in 'Figure 4.1.1', into the housing.
Slowly rotate the handle in the direction of
cranking until it fully engages.
Figure 4.2.4 Starting Handle Housing
Figure 4.1.3 Cold Start
3. Replace the plunger and inject the oil just before starting
the engine.
CAPTION
The device must not be used more than three times in
succession during the same attempt to start the engine.
4.2 Hand Starting
Before attempting to start the engine refer to "Starting Handle
Precautions".
1. Select the excess fuel position by turning the engine control
lever anti-clockwise to the ‘STOP’ position and releasing it.
T SERIES ENGINES WORKSHOP MANUAL
59
Figure 4.1.3 Cold Start
3.Replace the plunger and inject the oil just before
starting the engine.
CAUTION
The device must not be used more than three
times in succession during the same attempt to
start the engine.
4.2 HAND STARTING
Before attempting to start the engine refer to
"Starting Handle Precautions".
1.Select the excess fuel position by turning the
engine control lever anti-clockwise to the ‘STOP’
position and releasing it.
Figure 4.2.1 The Engine Control
2.If a variable speed control lever is fitted move it
to the fast position.
3.Move the decompressor lever towards the
flywheel.
Figure 4.2.3 Decompressor Lever
A - TS/TR; B - TX
4.If the ambient temperature is below -10°C
(14°F) refer to "Cold Starting Aid - TS/TR".
5a.
If using a non-limited kick-back handle:
Insert the correct handle, refer to 'A' in 'Figure
4.1.1', into the starting housing.
Figure 4.2.3 Starting Handle Housing
Slowly rotate the handle in the direction of
cranking until it fully engages.
5b. If using a limited kick-back handle:
Swivel the starting handle housing cover (A) to
one side and insert the correct handle, refer to 'B'
in 'Figure 4.1.1', into the housing.
Slowly rotate the handle in the direction of
cranking until it fully engages.
Figure 4.2.4 Starting Handle Housing
Figure 4.2.1 The Engine Control
2. If a variable speed control lever is fitted move it to the fast
position.
3. Move the decompressor lever towards the flywheel.
T SERIES ENGINES WORKSHOP MANUAL
59
Figure 4.1.3 Cold Start
3.Replace the plunger and inject the oil just before
starting the engine.
CAUTION
The device must not be used more than three
times in succession during the same attempt to
start the engine.
4.2 HAND STARTING
Before attempting to start the engine refer to
"Starting Handle Precautions".
1.Select the excess fuel position by turning the
engine control lever anti-clockwise to the ‘STOP’
position and releasing it.
Figure 4.2.1 The Engine Control
2.If a variable speed control lever is fitted move it
to the fast position.
3.Move the decompressor lever towards the
flywheel.
Figure 4.2.3 Decompressor Lever
A - TS/TR; B - TX
4.If the ambient temperature is below -10°C
(14°F) refer to "Cold Starting Aid - TS/TR".
5a. If using a non-limited kick-back handle:
Insert the correct handle, refer to 'A' in 'Figure
4.1.1', into the starting housing.
Figure 4.2.3 Starting Handle Housing
Slowly rotate the handle in the direction of
cranking until it fully engages.
5b. If using a limited kick-back handle:
Swivel the starting handle housing cover (A) to
one side and insert the correct handle, refer to 'B'
in 'Figure 4.1.1', into the housing.
Slowly rotate the handle in the direction of
cranking until it fully engages.
Figure 4.2.4 Starting Handle Housing
Figure 4.2.3 Decompressor Lever - A - TS/TR; B - TX
4. If the ambient temperature is below -10°C (14°F) refer to "Cold
Starting Aid - TS/TR".
5a.
If using a non-limited kick-back handle:
Insert the correct handle, refer to 'A' in 'Figure 4.1.1', into the
starting housing.
T SERIES ENGINES WORKSHOP MANUAL
59
Figure 4.1.3 Cold Start
3.Replace the plunger and inject the oil just before
starting the engine.
CAUTION
The device must not be used more than three
times in succession during the same attempt to
start the engine.
4.2 HAND STARTING
Before attempting to start the engine refer to
"Starting Handle Precautions".
1.Select the excess fuel position by turning the
engine control lever anti-clockwise to the ‘STOP’
position and releasing it.
Figure 4.2.1 The Engine Control
2.If a variable speed control lever is fitted move it
to the fast position.
3.Move the decompressor lever towards the
flywheel.
Figure 4.2.3 Decompressor Lever
A - TS/TR; B - TX
4.If the ambient temperature is below -10°C
(14°F) refer to "Cold Starting Aid - TS/TR".
5a.
If using a non-limited kick-back handle:
Insert the correct handle, refer to 'A' in 'Figure
4.1.1', into the starting housing.
Figure 4.2.3 Starting Handle Housing
Slowly rotate the handle in the direction of
cranking until it fully engages.
5b. If using a limited kick-back handle:
Swivel the starting handle housing cover (A) to
one side and insert the correct handle, refer to 'B'
in 'Figure 4.1.1', into the housing.
Slowly rotate the handle in the direction of
cranking until it fully engages.
Figure 4.2.4 Starting Handle Housing
Figure 4.2.3 Starting Handle Housing
Slowly rotate the handle in the direction of cranking until
it fully engages.
5b.
If using a limited kick-back handle:
Swivel the starting handle housing cover (A) to one side
and insert the correct handle, refer to 'B' in 'Figure 4.1.1',
into the housing.
Slowly rotate the handle in the direction of cranking until
it fully engages.
T SERIES ENGINES WORKSHOP MANUAL
59
Figure 4.1.3 Cold Start
3.Replace the plunger and inject the oil just before
starting the engine.
CAUTION
The device must not be used more than three
times in succession during the same attempt to
start the engine.
4.2 HAND STARTING
Before attempting to start the engine refer to
"Starting Handle Precautions".
1.Select the excess fuel position by turning the
engine control lever anti-clockwise to the ‘STOP’
position and releasing it.
Figure 4.2.1 The Engine Control
2.If a variable speed control lever is fitted move it
to the fast position.
3.Move the decompressor lever towards the
flywheel.
Figure 4.2.3 Decompressor Lever
A - TS/TR; B - TX
4.If the ambient temperature is below -10°C
(14°F) refer to "Cold Starting Aid - TS/TR".
5a. If using a non-limited kick-back handle:
Insert the correct handle, refer to 'A' in 'Figure
4.1.1', into the starting housing.
Figure 4.2.3 Starting Handle Housing
Slowly rotate the handle in the direction of
cranking until it fully engages.
5b. If using a limited kick-back handle:
Swivel the starting handle housing cover (A) to
one side and insert the correct handle, refer to 'B'
in 'Figure 4.1.1', into the housing.
Slowly rotate the handle in the direction of
cranking until it fully engages.
Figure 4.2.4 Starting Handle Housing
Figure 4.2.4 Starting Handle Housing
6. If the cold starting aid was not used turn the engine slowly
for up to 20 turns to prime the combustion chamber and
lubricating oil system.
7. Firmly hold the handle grip, with the thumb on top of the
grip as shown in 'Figure 4.1.2', and crank the engine really fast,
when sufficient speed is obtained move the decompressor
lever towards the gear end and continue to crank until the
engine fires.
Retaining a firm grip on the handle remove the handle from
the housing.
WARNING
Do not pull the starting handle away from the engine
while cranking.
8. If a variable speed control is fitted reduce the speed as
required.