Lincoln IMPINGER 1100 Скачать руководство пользователя страница 48

Страница: 48 / 72

Impinger II –1100 Series Service Manual - Domestic

TO REVERSE CONVEYOR DIRECTION ON STEPPER DRIVE SYSTEM

1. Shut off power at main breaker.

2. Remove conveyor.

3. Remove front control box cover.

4. Change position of dip switch #1 on stepper control board as described on page 46.

5. Reassemble in reverse order.

TRANSFORMER - STEPPER MOTOR CONTROL

1. Shut off power at main breaker.

2. Remove conveyor.

3. Remove front cover.

4. Disconnect transformer wire harness.

5. Remove two (2) mounting screws.

6. Reassemble in reverse order.

HALL EFFECT SENSOR - REPLACEMENT

Remove two (2) mounting screws and remove sensor from conveyor motor. Reinstall in

reverse order.

TYPE OF GAS

INCHES of

CENTIMETERS of

kPa

Mbar

WATER

COLUMN

WATER COLUMN

NATURAL GAS

3.5" WC

8.9 cm WC

.87kPa

8.70Mbar

L..P. GAS

10"WC

25.4 cm WC

2.48kPa

24.8Mbar

CITY/TOWN GAS

1.4"WC

3.56 cm WC

.35kPa

3.5Mbar

AIR PRESSURE SWITCH, BURNER OR OVEN CAVITY

TO REPLACE AIR SWITCH

1. Shut off power at main breaker.

2. Remove conveyor.

3. Remove rear control compartment cover.

4. Remove cover of air switch exposing adjustment screw.

5. Disconnect and mark wires for proper reassembly.

6. Remove air tube and remove switch from hanger.

7. Reinstall in reverse order, making sure wires are properly attached and air tube is properly attached,

unblocked and aligned properly to avoid crimping.

TO CALIBRATE AIR SWITCH

1. If switch will not activate when blower pressure is supplied, turn adjustment screw counter clockwise (-).

2. If switch will not deactivate when blower pressure is eliminated, turn adjustment clockwise (+).

Содержание IMPINGER 1100









































































Результаты поиска

Содержание IMPINGER 1100

Отзывы:

Бренды по названию

Популярные бренды

Lincoln IMPINGER 1100, Руководство по обслуживанию

Результаты поиска

Содержание IMPINGER 1100

Отзывы:

Бренды по названию

Популярные бренды