Lincoln IMPINGER 1100 Скачать руководство пользователя страница 37

Страница: 37 / 72

Impinger II –1100 Series Service Manual - Domestic

6. Remove 4 nuts from burner manifold and remove valve assembly.

7. Remove piping from solenoid valve.

8. Reassemble in reverse order.

NOTE:

Some piping changes may be required. See instructions supplied with replacement part.

HEATING ELEMENTS

1. Shut off power at main breaker.

2. Remove back cover.

3. Disconnect heater element wire and mark for reassembly.

4. Disconnect motor wiring and mark for reassembly.

5. Remove oven back from oven.

6. Remove fan shroud.

7. Heater element may now be unbolted and removed.

8. Check heater elements to be sure they are the proper replacement.

9. Reassemble in reverse order.

NOTE

: Be sure the lead terminals are tight.

IGNITION CONTROL

1. Shut off power at main breaker.

2. Shut of the gas supply in the main line to the oven.

3. Remove conveyor.

4. Remove the front control compartment cover.

Note: After S/N 2011383 a removable drip tray is located above the ignition control.

5. Disconnect the wires from the ignition control and mark their location for reinstallation.

6. Remove the 4 mounting screws and remove the control.

7. Reassemble in reverse order.

8. Turn on electrical power and gas supply, then check the system for proper operation.

VALVE

GND

25 V

GND

BURNER
GROUND

L 2

NEUTRAL

HSI

120 V

HSI

120 V

L 1
HOT

YELLOW

IGNITION CONTROL

TRANSFORMER, STEP DOWN 24 VAC

1. Shut off power at the main breaker.

2. Remove conveyor.

3. Remove front control compartment cover.

4. Remove wires from transformer and mark for reassembly.

5. Remove 2 mounting screws and replace transformer.

6. Reassemble in reverse order.

BURNER VENTURI

See "Hot Surface Igniter"

Содержание IMPINGER 1100









































































Результаты поиска

Содержание IMPINGER 1100

Отзывы:

Бренды по названию

Популярные бренды

Lincoln IMPINGER 1100, Руководство по обслуживанию

Результаты поиска

Содержание IMPINGER 1100

Отзывы:

Бренды по названию

Популярные бренды