Lincoln IMPINGER 1100 Скачать руководство пользователя страница 46

Страница: 46 / 72

Impinger II –1100 Series Service Manual - Domestic

FUSEHOLDER

1. Shut off power at main breaker.

2. Remove conveyor.

3. Remove control compartment covers.

4. Remove wires and mark for reassembly.

5. Remove fuseholder.

6. Reassemble in reverse order.

POWER CORD

1. Shut off power at main breaker.

2. Remove conveyor.

3. Remove control compartment covers.

4. Unfasten and mark for reassembly power cord wires.

5. Remove locknut from strain relief and pull cord from oven.

6. Reassemble in reverse order.

STEPPER CONTROL-REPLACEMENT-ADJUSTMENT

Removal and Installation

1. Remove conveyor.

2. Remove control box cover - front.

3. Remove three (3) screws from control assembly.

4. Disconnect wiring (push on connectors) from control board.

NOTE: Proper location of connectors for reinstallation.

5. Reassemble in reverse order and check system operation.

6. Recalibrate conveyor control board.

WARNING: THIS CONTROL MUST NOT BE OPERATED WITH HEAT SINK DISCONNECTED OR

BURNOUT WILL OCCUR IN SECONDS.

Blue

Gray

Red

Brown

Red

POWER

J 5

J 4

J 3

J 1

J 6

LOCKED ROTOR

To T/T display

POTENTIOMETER

Max.
Conveyor
Speed Adj.

Min.
Conveyor
Speed Adj.

TIME/TEMP

Black to #4
White to #7

CURRENT SENSE
DO NOT ADJUST

Heat Sink

MOTOR

1. With power off, the five (5) dip switches located on the conveyor control (see drawing above ) should be

set as below.

Содержание IMPINGER 1100









































































Результаты поиска

Содержание IMPINGER 1100

Отзывы:

Бренды по названию

Популярные бренды

Lincoln IMPINGER 1100, Руководство по обслуживанию

Результаты поиска

Содержание IMPINGER 1100

Отзывы:

Бренды по названию

Популярные бренды