Lincoln IMPINGER 1100 Скачать руководство пользователя страница 39

Страница: 39 / 72

Impinger II –1100 Series Service Manual - Domestic

LAMP, PILOT BURNER

LENS, PILOT LAMP

1. Shut off power at main breaker.

2. Remove conveyor.

3. Remove front control compartment cover.

4. Remove terminals from pilot lamp.

5. Grasp body of the light assembly and slide to the side disengaging body from light lens.

6. Remove lens by pushing out from rear.

7. Reassemble in reverse order.

COUPLING, CONVEYOR DRIVE

FOR ALL 1100 MODELS

This coupling has a plastic or rubber sleeve connecting two metal drive ends.

The metal drive end on the conveyor side is secured by a ball plunger screw,

This is not a set screw and should never be over tightened.

PROCEDURE FOR ADJUSTING DRIVE COUPLING

1. Place one metal end on conveyor shaft.

2. Install ball plunger and adjust so the spring loaded ball will drop into the dimple on the flat of the conveyor

drive shaft. To test, apply pressure on metal end towards the conveyor. The ball detent should pop up out of

the dimple and coupling end will slide back to conveyor frame.

3. Place other drive end on motor shaft,

4. Push conveyor frame to front side of oven conveyor opening.

5. Adjust the metal drive end on conveyor shaft so ball detent is in the dimple.

6. Lift the conveyor drive side slightly and place sleeve on conveyor side metal drive end.

7. Adjust motor side coupling drive end so sleeve is now held in place between the drive ends and tighten set

screw on motor side firmly.

To remove conveyor, simply grasp the coupling sleeve and pull towards conveyor.

The sleeve and drive end will slide towards the conveyor and separate from the motor

drive.

GEARMOTOR, D.C., CONVEYOR

1. Shut off power at main breaker.

2. Remove conveyor.

3. Remove control compartment covers.

4. Remove metal drive end from the motor shaft.

5. Remove electrical leads from gearmotor assembly and mark for proper reassembly.

6. Remove 4 screws holding gearmotor to the side wall of control compartment.

7. To remove tach., optical encoder assembly, and coupling and encoder disc refer to the

following instructions.

8. Reassemble in reverse order using care to readjust motor properly to be in line

with conveyor coupling.

NOTE: If a new gearmotor is installed, the D.C. motor control board must be recalibrated.

COUPLING AND ENCODER DISC

1. Remove gearmotor assembly (See "GEARMOTOR" )

2. Remove dust cover above motor.

3. Loosen both allen set screws (.050 inch allen wrench) located on coupling hub.

4. Remove 3 screws from tach. bracket, loosen the 4th.

5. Remove encoder assembly, see "OPTICAL ENCODER ASSEMBLY" in following procedure.

6. Push coupling down on motor shaft. Swivel tach. bracket aside and remove coupling.

7. To install, push coupling on to motor shaft. The encoder disc must be nearest motor.

8. Refasten tach. bracket in proper alignment.

9. Tighten the set screw on the tach. side first maintaining the .010 minimum dimension between the coupling

hub and tach.

10. Pull the coupling apart (approximately 1/8",3.2mm) and fasten the motor side set screw.

Содержание IMPINGER 1100









































































Результаты поиска

Содержание IMPINGER 1100

Отзывы:

Бренды по названию

Популярные бренды

Lincoln IMPINGER 1100, Руководство по обслуживанию

Результаты поиска

Содержание IMPINGER 1100

Отзывы:

Бренды по названию

Популярные бренды