Lincoln IMPINGER 1100 Скачать руководство пользователя страница 4

Страница: 4 / 72

Impinger II –1100 Series Service Manual - Domestic

SEQUENCE OF OPERATIONS 1116 - 1117

MODEL 1116 / NATURAL GAS / 120 VAC / 60 HZ / 1 PHASE

MODEL 1117 / L.P GAS / 120 VAC / 60 HZ / 1 PHASE

POWER SUPPLY

Electrical power is supplied to the oven by a three conductor cord set. Voltage from

the black conductor to the white conductor is 120 VAC. The white conductor is

neutral. The green conductor is ground.

CONTROL BOX AUTO

When the temperature in the control box reaches 120°F ± COOL DOWN 3°(48.9°C

± 1.7°C), the Cooling Fan Thermostat will switch power to the Control Box Cooling

Fans. The thermostat will interrupt power to the fans when the control box

temperature falls to100°F ± 3° (37.8°C ± 1.7°C).

MAIN FAN CIRCUIT

Power is permanently supplied to the normally open contacts of the oven fan relay,

the normally open cooling fan thermostat, terminal #1 of the time delay relay and

the normally open main fan switch. Closing the main fan switch enables the 20

minutes time delay relay. The time delay relay supplies 120 VAC to the coil of the

main fan relay. These normally open contacts now close energizing the main fan

motor and the cooling fans. Closing the fan switch also energizes the time/temp

display, the heat and conveyor switches.

BURNER CIRCUIT

Closing the Burner Switch supplies 120 VAC through the 10 Amp Fuse, through

the Main Fan Motor Centrifugal Switch, and oven cavity High Limit Thermostat to

terminal L1 of the Ignition Control. The Centrifugal Switch of the Main Fan Motor

closes when the fan motor reaches 1600 RPM. The High Limit Thermostat opens

at 662°F(350°C) and may be manually reset after the sensing bulb temperature

drops 18°F(10°C).Power (120 VAC) is also supplied to the Burner Blower Motor.

As this motor reaches approximately 1600 RPM, its Internal Centrifugal Switch

closes, supplying 120 VAC through the normally closed Control Box High Limit

Thermostat, to the primary of the 24 VAC Transformer and the Temperature

Control. The Control Box High Limit Thermostat is manually re-settable and opens

when the control box reaches 170°F ± 5°(76°C ± 3°C). (Discontinued at S/N

2011383)

IGNITION CONTROL

The Ignition Control operates on both 24 VAC and 120 VAC. When the control is

energized by 24 VAC from the Transformer, 120 VAC is switched by the Ignition

Control to the Hot Surface Ignitor for 45 seconds for Hot Surface Ignitor warm up.

The Ignitor glows red, 24 VAC is switched to the gas valve which opens, and

ignition should now occur. If ignition does not occur in 6 seconds, the control will

lock out. To recycle after lockout, turn off the burner switch for 45 seconds and

then turn the switch back on.

TEMPERATURE CONTROL

When the Centrifigual Switch of the Burner Blower Motor closes, power is applied

to the Temperature Control. The 2.5K ohm Temperature Pot is adjusted to desired

temperature. The Thermocouple will provide varying millivolts to the Temperature

Controller. The Temperature Controller supplies 120 VAC to the Solenoid Valve at

intermittent intervals to maintain desired temperature.

CONVEYOR DRIVE

Closing the Fan Switch and the Conveyor Switch, supplies 120 VAC through 3

Amp Fuse to L1and L2 of the Motor Control Board. AC volts are converted to DC

by the Control Board and are supplied to the Motor from Board terminals A+ and A-

. Adjustment of the Speed Control Pot (5,000 ohm 10 turn pot) will change

resistance at terminals P1, P2, and P3 varying S/N 2011383 and above the DC

voltage to the motor. The speed of the Conveyor Motor Refer to page 26 will

increase or decrease as the DC voltage from the board increases or decreases

respectively. As the motor turns, it drives both the Reducer Gear Box and the

Tach. Generator. The Tach. Generator is a DC voltage Generator that supplies a

voltage to the DC Motor Control Board and is used as a reference for maintaining a

constant conveyor speed.

TIME/TEMP DISPLAY

The secondary output of the Transformer, is supplied to terminals 1, 2, and 3 of the

Time/Temp. Display. The secondary output of Transformer is nominally 12.5 to 15

VAC with a center tap. The voltage from center tap to each leg is 1/2 the

secondary voltage.

Содержание IMPINGER 1100









































































Результаты поиска

Содержание IMPINGER 1100

Отзывы:

Бренды по названию

Популярные бренды

Lincoln IMPINGER 1100, Руководство по обслуживанию

Результаты поиска

Содержание IMPINGER 1100

Отзывы:

Бренды по названию

Популярные бренды