Lexmark X925 7541-03 series Скачать руководство пользователя страница 125 | Manualshive

Страница: 125 / 500

background image

Diagnostic information

2-87

7541-03x

Go Back

Previous

Next

Words on fax are stretched

The sending machine had a temporary jam.

Incoming fax has blank spaces or poor quality

1.

The sending fax machine may be faulty.

2.

The sending fax machine may have a dirty document glass.

3.

A noisy phone line can cause errors.

4.

Check the MFP print quality by making a copy.

5.

The print cartridge may be empty. Replace as necessary.

No dial tone

Fax dials a number, but no connection is made

The other fax machine may be turned off. Ask the fax recipient to check their machine.

Step

Questions / actions

Yes

No

1

Is the phone line properly connected to
the modem card and the wall jack?

Go to step 3.

Go to step 2.

2

Properly connect the phone line to the
modem card and wall jack.

Did this fix the problem?

Problem resolved.

Go to step 3.

3

Test the phone line’s ability to send and
receive calls.

Did the phone line work properly?

Go to step 5.

Go to step 4.

4

Use the MFP on a properly functioning
phone jack.

Did this fix the problem?

Problem resolved.

Go to step 5.

5

Is the modem card cable properly
connected to the system board at J8 and
the modem card?

Go to step 7.

Go to step 6.

6

Properly connect the modem card cable
to the modem card and system board.

Did this fix the problem?

Problem resolved.

Go to step 7.

7

Check the modem card cable for
continuity. Is there continuity?

Go to step 8.

Replace the modem
card cable.

8

Check the voltages from connector
JMODEM1 on the RIP board. Check Pin
10 +3.3VDC, Pin 10 for +5VDC. 2, 4, 6,
and 8 are grounds. Are the signals or
voltages present?

Replace the modem
card.

Replace the RIP board.
See

“RIP board

removal” on
page 4-73

.

«
...
123
124
125
126
127
...
»

Содержание X925 7541-03 series





















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X925 7541-03 series

Sure shot 80 tele

Бренд: Canon Страницы: 24

iPF720 - imagePROGRAF Color Inkjet Printer

Бренд: Canon Страницы: 8

Бренд: Canon Страницы: 2

imageRUNNER ADVANCE C5255

Бренд: Canon Страницы: 64

Powershot A3100 IS

Бренд: Canon Страницы: 6

Multi Function Professional Puncher-A1

Бренд: Canon Страницы: 44

imagePROGRAF TC-20

Бренд: Canon Страницы: 44

Бренд: Canon Страницы: 88

Бренд: Xerox Страницы: 2

Бренд: Xerox Страницы: 16

7300DX - Phaser Color Laser Printer

Бренд: Xerox Страницы: 14

Бренд: Copystar Страницы: 4

Бренд: Xerox Страницы: 44

Бренд: Printronix Страницы: 9

Бренд: Oce Страницы: 90

Бренд: Xante Страницы: 31

Бренд: J&Maya Страницы: 21

Бренд: Oki Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды