Lexmark X925 7541-03 series Скачать руководство пользователя страница 151 | Manualshive

Страница: 151 / 500

background image

Diagnostic aids

3-13

7541-03x

Go Back

Previous

Next

Energy Conserve

When Energy Conserve is on, the customer does not have access to disable the Sleep Mode function. When
Energy Conserve is off, Disable appears as an additional menu item in the Sleep Mode menu. This setting only
affects the values that are displayed in the Sleep Mode menu.

Fax Low Power Support

This menu has the following settings:

Auto

—The printer checks the Caller ID Pattern setting to determine if the fax chip should enter low power

mode.

Permit Sleep

—The fax chip enters low power mode when needed, regardless of the Caller ID Patter

setting.

Disable Sleep

—The fax chip never enters low power mode.

Min Copy Memory

This menu lets you select the amount of memory dedicated to storing copy jobs. The values may be 25 MB, 35
MB, 50 MB, 80 MB, and 100 MB. The default is 80 MB. Values will be displayed only if the amount of installed
DRAM is at least twice the amount of the value. For example, at least 200 MB of installed DRAM is required to
display the 100 MB selection.

NumPad Job Assist

When this setting is set to On, a user can initiate scanner-related jobs, and enter values for a limited number of
settings related to those jobs, using the keypad.

Touch

Back

to exit without changing the setting.

Format Fax Storage

This setting enables you to format the non-volatile storage used for storing faxes.

Note:

If an advanced password has been established, you must enter this password in order to change the

setting.

Fax Storage Location

This menu allows you to select either NAND or the printer hard disk (Disk) as the fax storage location. If the
printer hard disk is removed, then this menu no longer appears.

Auto Align Adj

The printer automatically runs a Toner Patch Sensing (TPS) diagnostic after certain key events. Depending on
the type of event, the results of the diagnostics can trigger either a color adjust calibration or an alignment
calibration. If necessary, the printer will automatically adjust the alignment.

If Auto Align Adj is set to Off, then the diagnostic still runs, but the printer will not use the resulting data to
automatically adjust alignment. This could eventually lead to the user having to adjust alignment manually.
Therefore, Auto Align Adj should not be set to Off during normal printer usage.

«
...
149
150
151
152
153
...
»

Содержание X925 7541-03 series





















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X925 7541-03 series

Бренд: Olympus Страницы: 71

Бренд: DataCard Страницы: 17

Бренд: DataCard Страницы: 24

Бренд: oliser Страницы: 6

Replicator Mini+

Бренд: MakerBot Страницы: 2

Replicator Mini Compact

Бренд: MakerBot Страницы: 38

Бренд: MakerBot Страницы: 14

Бренд: SainSmart Страницы: 13

Бренд: Xerox Страницы: 12

Бренд: Pantum Страницы: 115

Бренд: BIXOLON Страницы: 31

Бренд: Roland Страницы: 36

MAGICARD 300plus

Бренд: Ultra electronics Страницы: 45

Бренд: POS-TECHNOLOGY Страницы: 40

WorkCentre 3615DN

Бренд: Xerox Страницы: 4

Бренд: MIMAKI Страницы: 28

Бренд: Graphic Products Страницы: 28

Бренд: Xerox Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды