Lexmark X925 7541-03 series Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 500

background image

2-36

Service Manual

7541-03x

Go Back

Previous

Next

ADF paper jam service check

Note:

This service check should be used if the paper feeds and jams in the ADF. If the paper is not feeding into

the ADF see

“280.06 Paper missing” on page 2-29

. If the paper fails to eject from the ADF see

Step

Questions / actions

Yes

No

1

If the ADF is multi-feeding, check for dirt on
the ADF separator pad and ADF separator
rollers. Are they dirty?

Clean them with a lint free
cloth and isopropyl alcohol.

Replace the separator pad
and ADF pick roll.

2

If the paper is skewing when it is fed into the
ADF, check the paper guide width. Is it set
correctly?

Go to step 3.

Set the paper guides so
they contact the edges of
the paper.

3

If paper is skewing when fed or jamming
check to see if the top cover is open or ajar.
Is the ADF top cover open or ajar?

Properly close the top
cover.

If the paper is jamming in
the ADF, go to step 6

4

Is paper failing to feed into the ADF?

Go to step 5.

There is no issue.

5

Check the sensor (ADF paper present) for
proper operation.

1. Enter the Diagnostics Menu.
2. Touch

SCANNER TESTS.

3. Touch

Sensor Tests.

4. Observe the line “sensor (ADF paper

present)”

Are the sensors working properly?

Go to step 6

Go to step 9.

6

Check the leading edge of the paper to
ensure the paper is not curled or bent in a
way that would keep it from contacting the
paper present sensor actuator. Is the paper
damaged?

Bad media. Replace the
media

Go to step 7.

7

Check for dirt in the ADF scan sensor, paper
in sensor and paper pass sensor. See

“Flatbed / ADF sensors” on page 5-3

for

their locations. Are the sensors clean?

Clean the sensors, or
remove debris from the
scan sensor actuator.

Go to step 8.

8

Is the sensor actuator on the ADF scan
sensor damaged?

Replace the scan sensor
actuator.

Go to step 9.

9

Are the sensor cable connectors properly
connected on the ADF relay card?

Go to step 10.

Go to step 10.

10

Connect the cables. Did this fix the issue?

Problem resolved.

Go to step 11.

11

Check the ADF motor assembly for proper
connection to J2 and J6 on the ADF relay
card. Are the motors properly connected?

Go to step 12

Go to step 13.

12

Connect the cables. Did this fix the issue?

Problem resolved

Got to step 13.

13

Replace the ADF motor assembly. Did this
fix the issue?

Problem resolved

Go to step 14.

14

Check the ADF cable for continuity. Is there
continuity?

Go to step 15.

Replace the ADF cable.

15

Replace the ADF relay card. Did this solve
the problem?

Problem resolved

Go to step 16.

«
...
72
73
74
75
76
...
»

Содержание X925 7541-03 series





















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X925 7541-03 series

Бренд: Xerox Страницы: 2

Бренд: Xerox Страницы: 2

Бренд: Pantum Страницы: 94

WORKCENTRE 5735

Бренд: Xerox Страницы: 50

Бренд: Canon Страницы: 521

Бренд: Canon Страницы: 456

Бренд: FujiFilm Страницы: 34

Бренд: Xerox Страницы: 14

Бренд: Olivetti Страницы: 111

Бренд: AstroJet Страницы: 97

Бренд: Ricoh Страницы: 17

Бренд: Gerber Страницы: 163

Бренд: Xerox Страницы: 8

SignJet JS310 Series

Бренд: GRAPHTEC Страницы: 83

634dte - X B/W Laser

Бренд: Lexmark Страницы: 148

ECP- Magenta Toner Premix/Concentrate for ECP 42

Бренд: Xerox Страницы: 2

RXi HMI GFK-3233A

Бренд: Emerson Страницы: 20

Бренд: Epson Страницы: 59

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды