Lexmark X925 7541-03 series Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 500

background image

Edition: November 14, 2014

The following paragraph does not apply to any country where such provisions are inconsistent with local law

:

LEXMARK INTERNATIONAL, INC. PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or
implied warranties in certain transactions; therefore, this statement may not apply to you.

This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the
information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the
programs described may be made at any time.

Comments may be addressed to Lexmark International, Inc., Department D22X/002-1, 740 West New Circle Road,
Lexington, Kentucky 40550, U.S.A or e-mail at [email protected]. Lexmark may use or distribute any
of the information you supply in any way it believes appropriate without incurring any obligation to you.

References in this publication to products, programs, or services do not imply that the manufacturer intends to make these
available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or
imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that
does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in
conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the
user’s responsibility.

Lexmark, Lexmark with diamond design, and MarkNet are trademarks of Lexmark International, Inc., registered in the
United States and/or other countries.

Optra Forms is a trademark of Lexmark International, Inc.

PostScript® is a registered trademark of Adobe Systems Incorporated.

PCL® is a registered trademark of the Hewlett-Packard Company.

All other trademarks are the property of their respective owners.

© 2006 Lexmark International, Inc.

All

rights

reserved.

UNITED STATES GOVERNMENT RIGHTS

This software and any accompanying documentation provided under this agreement are commercial computer software
and documentation developed exclusively at private expense.

P/N 12G0474

7541-03x

«
1
2
3
4
...
»

Содержание X925 7541-03 series





















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X925 7541-03 series

Бренд: Samsung Страницы: 165

Бренд: Samsung Страницы: 2

Inkjet SCX-1150F

Бренд: Samsung Страницы: 66

Бренд: Samsung Страницы: 155

CLX-3170FN series

Бренд: Samsung Страницы: 220

CLX 6210FX - Color Laser - All-in-One

Бренд: Samsung Страницы: 36

CLX-3160 Series

Бренд: Samsung Страницы: 139

Бренд: Samsung Страницы: 8

Lazett Combo SCX-4016

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 319

Бренд: Samsung Страницы: 322

Бренд: Samsung Страницы: 340

Бренд: Samsung Страницы: 349

Бренд: Samsung Страницы: 330

Бренд: Samsung Страницы: 315

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 232

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды