Lexmark X925 7541-03 series Скачать руководство пользователя страница 47

Страница: 47 / 500

Diagnostic information

2-9

7541-03x

Go Back

Black page

No print

Step

Action and questions

Yes

Inspect the contact points for the imaging unit and the
printer. Are they clean and free of debris?

Go to step 3

Go to step 2

Clean the contacts. Did this fix the issue?

Problem resolved

Go to step 3.

Check the sub frame for bent springs, or contacts. Are
the contacts on the sub frame damaged?

Replace the sub
frame.

Go to step 4.

Check the HVPS for proper installation. Are the screws
securing the HVPS to the subframe secure?

Go to step 5

Tighten the
screws.

Disconnect and reconnect the HVPS cable at the
bottom of the HVPS. Did this fix the problem?

Problem resolved

Go to step 6.

Replace the HVPS. Did this fix the problem?

Problem resolved

Contact your
second level
support.

Step

Action and questions

Yes

Check the paper in the printer for moisture. Is the
paper damp?

Replace the
paper with dry
paper.

Go to step 2.

Check for dewing or moisture on the LED printheads.
Is there moisture on the printheads?

Let the
printheads dry.
Move the printer
to a less humid
location if
needed.

Go to step 3.

Using the Administrative menu, move the transfer belt
to the up and down position. Does the belt move?

Go to step 4.

Replace the belt

Check the transfer roll for proper installation. Is the
transfer roll installed correctly?

Go to step 5.

Reinstall the
transfer roll.

Check the transfer roll contacts for dirt or wear. Are the
transfer roll contacts clean?

Go to step 6.

Clean the
contacts.

Check the LED ribbon cables for proper connection at
both ends. Are the LED ribbon cables properly
installed?

Go to step.7

Properly install
the ribbon
cables.

Check the LED ribbon cable connectors on the
printhead controller board for +5V DC. Is the voltage
correct?

Go to step.8

Replace the
printhead
controller board.

Check all the connectors on the printhead controller
board. Are they properly connected

Go to step.9

Properly connect
the connectors.

Replace the printhead controller board. Did this fix the
problem?

Problem
resolved.

Contact second
level support.

Содержание X925 7541-03 series





















































































































































































































































































































































































































































































































Результаты поиска

Содержание X925 7541-03 series

Отзывы:

Похожие инструкции для X925 7541-03 series

Бренды по названию

Популярные бренды

Lexmark X925 7541-03 series, Руководство по обслуживанию

Результаты поиска

Содержание X925 7541-03 series

Отзывы:

Похожие инструкции для X925 7541-03 series

Бренды по названию

Популярные бренды