Lexmark X925 7541-03 series Скачать руководство пользователя страница 166 | Manualshive

Страница: 166 / 500

background image

3-28

Service Manual

7541-03x

Go Back

Previous

Next

SCANNER TESTS

Scanner Calibration Reset

This option resets the scanner calibration values to factory default settings. This should be done after you
replace the flatbed scanner unit.

For more information, see

“Calibrating the scanner” on page 4-211

.

Note:

Be sure the scanner glass and backing material are clean before performing this test.

ASIC Test

This test initiates a scan of the scanner ASIC memory. This is a pass/fail test.

Press

Stop

(

X

) to clear the results message from the screen.

Feed Test

This test performs a continuous feed test of either the flatbed scanner or ADF without producing any printed
output or incrementing any of the scanner-related counters.

For an ADF test, select a paper size. The ADF then performs a duplex scan using the chosen paper size
settings. For a flatbed test, the scanner traverses the entire length of the flatbed.

Press

Stop

(

X

) to end the test.

Sensor Test

This test checks each scanner-related sensor and returns “Closed” or “Open” for each.

Sensor (ADF Paper Present)

—”0” means paper is not present in the ADF.

Sensor (FB Cover Open)

—”0” means the flatbed cover is down.

Sensor (Home Sensor)

—”1” means the CCD is in the home position.

Sensor (Skew Sensor)

—”0” means the actuator is in the up position.

Sensor (ADF Cover open)

—”0” means the ADF cover is closed.

Sensor (ADF Exit)

—”0” means paper is not present in exit sensor.

Sensor (ADF Scan Sensor)

—”0” means paper is not present in the scan sensor.

Sensor (ADF Jam Sensor)

—”0” means paper is not present in the jam sensor.

Sensor (FB short)

—”0” means sensor open.

Sensor (FB medium)

—”0” means sensor open.

Sensor (FB long)

—”0” means sensor open.

Sensor (ADF long)

—”0” means sensor open.

Sensor (ADF width 1)

—”0” means sensor open.

Sensor (ADF width 2)

—”0” means sensor open.

ADF Magnification

Use this menu to adjust the ADF magnification from -99 to 100. The default setting is 0.

EXIT DIAGNOSTICS

Select

EXIT DIAGNOSTICS

to exit the Diagnostics menu and return to normal mode.

«
...
164
165
166
167
168
...
»

Содержание X925 7541-03 series





















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X925 7541-03 series

Бренд: Oki Страницы: 48

Бренд: Oki Страницы: 20

Бренд: Oki Страницы: 42

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 8

Бренд: Oki Страницы: 13

Бренд: Oce Страницы: 2

Бренд: Oki Страницы: 193

Бренд: Canon Страницы: 542

7400DT - Phaser Color LED Printer

Бренд: Xerox Страницы: 20

Donation Point Even

Бренд: Quest Payment Systems Страницы: 2

Бренд: Xerox Страницы: 70

Бренд: 3nStar Страницы: 8

Бренд: Konica Minolta Страницы: 4

Бренд: Creality Страницы: 24

Бренд: Konica Minolta Страницы: 108

Бренд: Nexa Страницы: 2

CraftBot PlusPro

Бренд: CraftUnique Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды