manualshive.com logo in svg

Lexmark X925 7541-03 series, Руководство по обслуживанию

Lexmark X925 7541-03 серия - это многофункциональное устройство, обеспечивающее высокое качество печати и сканирования. Для удобства пользователей доступен бесплатный загрузка сервисного руководства на manualshive.com. Получите детальное описание и инструкции по эксплуатации для наилучшей производительности устройства.

Поделиться
Скачать
background image

4-2

  Service Manual

7541-03x

Go Back

Previous

Next

Flatbed / ICC card NVRAM

The flatbed ICC card contains NVRAM. Do not use an ICC card from another X925 printer. Using an ICC card or 
complete flatbed assembly from another machine will result in a 950.10 NVRAM mismatch error.

RIP board/operator panel replacement

This procedure should only be followed if both the RIP board and operator panel fail. If you only need to replace 
one of the FRUs follow the startup procedure described in the FRU’s removal procedure.

CAUTION - POTENTIAL INJURY: 

There is danger of explosion if a lithium battery is incorrectly 

replaced. Replace it only with the same or an equivalent type of lithium battery. Do not recharge, 
disassemble, or incinerate a lithium battery. Discard used batteries according to the manufacturer's 
instructions and local regulations.

Warning:  

If the operator panel and the RIP board are being replaced at the same time, replace the parts in this 

order to avoid damage to the machine. 

1.

Replace the RIP card first. Note: Do not replace the new operator panel and RIP card in the machine at the 
same time. 

2.

After installing the new RIP card, and before installing the new operator panel, start the printer into 
diagnostics mode. 

3.

After the printer has completed startup, turn off the printer and replace the operator panel. 

Note:  

Note: If the operator panel display has failed, the printers’ startup cycle is complete when the driver 

motor and fans shut down, and the machine is quiet. 

4.

After installing the new operator panel, start the printer in to diagnostics mode, and allow the printer to go 
through a complete startup cycle and the display to go to Ready. 

5.

If the problems persist, leave the new operator panel in the machine, place the old RIP card back in the 
machine, and start it up. After the machine startup, shut down the machine, and install the new RIP card. 
After installing the new RIP card, restart the machine, and let it go through the startup cycle. 

After this procedure is completed successfully, there is no need to adjust any settings. 

If the above procedure fails, you must contact the technical support center for further instructions.

Printhead controller board / engine board replacement

This procedure should only be followed if both the printhead controller board and engine board are being 
replaced. If you only need to replace one of the FRUs follow the startup procedure described in the FRU’s 
removal procedure.

Warning:  

If the printhead controller board and the engine board are being replaced at the same time, replace 

the parts in this order to avoid damage to the machine. 

1.

Replace the printhead controller board first. Do not replace the printhead controller board and engine 
board in the machine at the same time. 

2.

After installing the new printhead controller board, and before installing the new engine board, start the 
printer. 

3.

After the printer has completed startup, turn off the printer and replace the engine board. 

4.

After installing the new engine board, start the printer, and allow the printer to go through a complete 
startup cycle and the display to go to Ready. 

If the problems persist, leave the new engine board in the machine, place the old printhead controller board back 
in the machine, and start it up. After the machine startup, shut down the machine, and install the new printhead 
controller board. After installing the new printhead controller board, restart the machine, and let it go through the 
startup cycle. After this procedure is completed successfully, there is no need to adjust any settings. 

If the above procedure fails, you must contact the technical support center for further instructions.

Содержание X925 7541-03 series





















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X925 7541-03 series

Canon ImageCLASS MF3240 Series Advanced Manual preview
ImageCLASS MF3240 Series
Бренд: Canon Страницы: 62
Canon ImageCLASS MF4270 Operation Manual preview
ImageCLASS MF4270
Бренд: Canon Страницы: 226
Canon imageCLASS D660 Setup Instructions preview
imageCLASS D660
Бренд: Canon Страницы: 8
Canon ImageCLASS MF3240 Series Basic Manual preview
ImageCLASS MF3240 Series
Бренд: Canon Страницы: 136
Canon Color imageRUNNER C5180 Series Service Manual preview
Color imageRUNNER C5180 Series
Бренд: Canon Страницы: 851
Canon imageCLASS D320 Printer Manual preview
imageCLASS D320
Бренд: Canon Страницы: 121
Canon imageCLASS MF212w User Manual preview
imageCLASS MF212w
Бренд: Canon Страницы: 236
Canon imageCLASS D760 Reference Manual preview
imageCLASS D760
Бренд: Canon Страницы: 82
Canon imageclass LBP251dw Settings Manual preview
imageclass LBP251dw
Бренд: Canon Страницы: 72
Canon ImageCLASS MF4270 Basic Operation Manual preview
ImageCLASS MF4270
Бренд: Canon Страницы: 248
Canon ImageCLASS MF4270 Starter Manual preview
ImageCLASS MF4270
Бренд: Canon Страницы: 36
Canon imageCLASS D760 Setup Instructions preview
imageCLASS D760
Бренд: Canon Страницы: 8
Canon imageCLASS MF4100 Series Service Manual preview
imageCLASS MF4100 Series
Бренд: Canon Страницы: 140
Canon imageclass LBP251dw Getting Started preview
imageclass LBP251dw
Бренд: Canon Страницы: 116
Canon imageCLASS D860 Basic Manual preview
imageCLASS D860
Бренд: Canon Страницы: 73
Canon imageCLASS D1320 Starter Manual preview
imageCLASS D1320
Бренд: Canon Страницы: 36
Canon ImageCLASS MF3240 Series Starter Manual preview
ImageCLASS MF3240 Series
Бренд: Canon Страницы: 15
Canon imageCLASS D550 Basic Operation Manual preview
imageCLASS D550
Бренд: Canon Страницы: 116

Бренды по названию

Популярные бренды

Загрузить еще бренды