Lexmark X925 7541-03 series Скачать руководство пользователя страница 126 | Manualshive

Страница: 126 / 500

background image

2-88

Service Manual

7541-03x

Go Back

Previous

Next

Other service checks

Networking service check

Note:

Before starting this service check, print out the network setup page. This page is found under Menu -

Reports - Network Setup Page. Consult the network administrator to verify that the physical and wireless
network settings displayed on the network settings page for the device are properly configured. If a wireless
network is used, verify that the printer is in range of the host computer or wireless access point, and there is no
electronic interference. Have the network administrator verify that the device is using the correct SSID, and
wireless security protocols. For more network troubleshooting information, consult the Lexmark Network Setup
Guide.

Step

Questions / actions

Yes

No

1

If the device is physically connected to the
network, verify that the ethernet cable is
properly connected on both ends.

Is the cable properly connected?

Go to step 3.

If the network is wireless,
got to step 3.

Go to step 2.

2

Connect the ethernet cable.

Did this fix the problem?

Problem resolved

Go to step 3.

3

Check the printer’s online status under Printers
and Faxes on the host computer. Delete all
print jobs in the print queue.

Is the printer online and in a

Ready

state.

Go to step 5.

Go to step 4.

4

Change the printer status to online.

Did this fix the issue?

Problem resolved.

Go to step 5.

5

Does the IP address displayed on the network
settings page match the IP address in the port
of the drivers using the printer?

Go to step 10.

Go to step 6.

6

Does the LAN use DHCP?

Note:

A printer should use a static IP

address on a network.

Go to step 7.

Go to step 9.

7

Are the first two segments if the IP address
169.254?

Go to step 8.

Go to step 9

8

POR the printer.

Is the problem resolved?

Problem resolved

Go to step 10.

9

Reset the address on the printer to match the
IP address on the driver.

Did this resolve the issue?

Problem fixed.

Go to step 10.

10

Have the network admin verify that the printer
and PC’s IP address have identical subnet
addresses.

Are the subnet addresses the same?

Go to step 12.

Go to step 11.

11

Using the subnet address supplied by the
network admin, assign a unique IP address to
the printer.

Note:

The printer IP address should match

the IP address on the printer driver.

Did this fix the problem?

Problem resolved.

Go to step 12.

«
...
124
125
126
127
128
...
»

Содержание X925 7541-03 series





















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X925 7541-03 series

Бренд: CAB Страницы: 263

Бренд: Panasonic Страницы: 102

Бренд: Labelmate Страницы: 2

Бренд: LabelTac Страницы: 15

Бренд: BALCO Страницы: 24

Бренд: Canon Страницы: 36

Бренд: Canon Страницы: 62

WorkCentre 4260S

Бренд: Xerox Страницы: 8

Бренд: Canon Страницы: 738

Бренд: Samsung Страницы: 143

imageRUNNER 6570

Бренд: Canon Страницы: 274

Бренд: Xerox Страницы: 14

Бренд: Xerox Страницы: 2

Бренд: Ricoh Страницы: 2

mC-Print3 MCP31LB

Бренд: Star Страницы: 12

Бренд: SPRT Страницы: 15

Бренд: DNP Страницы: 2

Бренд: Kyocera Mita Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды