Lexmark X925 7541-03 series Скачать руководство пользователя страница 152 | Manualshive

Страница: 152 / 500

background image

3-14

Service Manual

7541-03x

Go Back

Previous

Next

Color Alignment

Note:

This menu item is not accessible in the Diagnostics menu.

To perform a color alignment, enter the administrative menus when the printer is in Ready state, and then
navigate to:

Settings

>

Print Settings

>

Quality Menu

>

Color Adjust

The printer will perform a color alignment, and then return to Ready state when the procedure is finished.

ADF Edge Erase

The ADF Edge Erase setting specifies, in millimeters, the size of a border around the scanned image that will be
erased. For copies, the printed page will always have a at least a 2-mm no-print border. The larger of the 2-mm
no-print border and the Edge Erase setting will be used in this situation.

FB Edge Erase

The FB Edge Erase setting specifies, in millimeters, the size of a border around the scanned image that will be
erased. For copies, the printed page will always have a at least a 2-mm no-print border. The larger of the 2-mm
no-print border and the Edge Erase setting will be used in this situation.

Scanner Manual Registration

Use this menu to adjust the scanner margins after you replace any of the following parts:

–

Flatbed scanner assembly

–

ADF unit assembly

–

Flatbed scanner CCD assembly

For more information, see

“Adjusting scanner registration” on page 4-212

.

Note:

The Scanner Manual Registration menu does not appear if Disable Scanner is set to Auto Disabled.

Disable Scanner

Use this setting to enable or disable the flatbed scanner and ADF.

Note:

Auto Disabled can only be saved by the printer in response to failed scanner operation. Users cannot

save this setting.

Paper Prompts

Setting Paper Prompts controls which tray a change prompt is directed to when paper is sensed to be the wrong
size.

Envelope Prompts

Env Prompts controls which tray a change prompt is directed to when the envelopes are sensed to be the wrong
size.

«
...
150
151
152
153
154
...
»

Содержание X925 7541-03 series





















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X925 7541-03 series

Бренд: MAKERGEAR Страницы: 8

Aficio MP C6503SP

Бренд: Ricoh Страницы: 264

Бренд: Oki Страницы: 192

Бренд: UEi Страницы: 4

Бренд: Oki Страницы: 157

Бренд: X-media Страницы: 10

Бренд: formlabs Страницы: 4

4510B - Phaser B/W Laser Printer

Бренд: Xerox Страницы: 10

Бренд: Kyocera Страницы: 173

imageCLASS LBP247dw

Бренд: Canon Страницы: 32

Бренд: Canon Страницы: 50

imagePRESS V1000

Бренд: Canon Страницы: 123

Бренд: Creativity Страницы: 32

Бренд: Epson Страницы: 4

Бренд: Epson Страницы: 4

Бренд: Tektronix Страницы: 11

Бренд: Tektronix Страницы: 2

Бренд: Tektronix Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды