Lenovo RackSwitch G8264CS Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 96

background image

60

G8264CS Installation Guide

To remove one of the installed SFP, SFP+, or QSFP+ transceiver modules from the

switch, complete the following steps.
1. Disconnect the port cable from the transceiver.
2. Pull down the locking lever to release the transceiver.
3. Gently slide the transceiver out of the switch.
4. After you remove the transceiver, replace the safety cap.

To replace the transceiver module, see the appropriate section under

“Installing Port

Transceivers” on page 52

Removing and Replacing a Power Supply Module

The rear panel of the G8264CS has two bays for hot-swap power supply modules.

Two active power supply modules are required for load-sharing and redundancy. If

one power supply module fails, you can replace it without powering off the switch or

disrupting switch functions.

For proper airflow when operating the switch with only one power supply module,

the empty power supply bay must be closed by a blank power filler plate.

Removing the Power Supply Module

Statement 5

CAUTION:
The power control button on the device and the power switch on the power
supply do not turn off the electrical current supplied to the device. The device
also might have more than one power cord. To remove all electrical current
from the device, ensure that all power cords are disconnected from the power
source.

1

2

«
...
58
59
60
61
62
...
»

Содержание RackSwitch G8264CS

































































































Отзывы:

Нет отзывов

Похожие инструкции для RackSwitch G8264CS

Бренд: Panasonic Страницы: 20

Бренд: Panasonic Страницы: 281

Бренд: IDEC Страницы: 5

Бренд: IDEC Страницы: 7

Sierra Pro XL 1616V3

Бренд: Kramer Страницы: 2

Бренд: rako Страницы: 4

Бренд: DAITEM Страницы: 37

Champion KD-2X1

Бренд: Key Digital Страницы: 12

Бренд: LEGRAND Страницы: 12

Бренд: Optical Systems Design Страницы: 20

Бренд: WIKA Страницы: 8

Бренд: Siqura Страницы: 2

Бренд: IOGear Страницы: 1

Бренд: Delta Electronics Страницы: 1

Бренд: Extron electronics Страницы: 137

Бренд: Key Digital Страницы: 20

Бренд: Uniclass Страницы: 32

Бренд: Raritan Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды