Lenovo RackSwitch G8264CS Скачать руководство пользователя страница 93

Страница: 93 / 96

Appendix C. Technical Specifications

The G8264CS technical specifications are described in the following sections.

Physical Characteristics

The physical characteristics of the G8264CS are listed in the following table.

Environmental Specifications

The environmental specifications for the G8264CS are listed in the following table.

Table 15. Physical characteristics

Specification

Physical characteristics

Dimensions (H x W x D)

4.45 x 43.9 x 48.26 cm

(1.75 x 17.3 x 19 in)

Weight

10.35 kg (22.1 lb) maximum

Airflow

Available options for rear to front,

or front to rear airflow

Table 16. G8264CS environmental specifications

Specification

Measurement

Temperature, ambient operating

0°C to +40°C (32° to 104°F)

Temperature (one fan failure), operating 0°C to +35°C (32° to 95°F)

Temperature, storage

-40°C to +85°C (-40° to 185°F)

Relative humidity (non-condensing),

operating

10 to 90%

Relative humidity (non-condensing),

storage

10 to 90%

Altitude, operating

1,800 m (6,000 ft)

Altitude, storage

12,190 m (40,000 ft)

Acoustic noise

Less than 65dB

Heat dissipation

1,127 BTU/h (typical)

1,280 BTU/h (maximum)

Содержание RackSwitch G8264CS

































































































Результаты поиска

Содержание RackSwitch G8264CS

Отзывы:

Похожие инструкции для RackSwitch G8264CS

Бренды по названию

Популярные бренды

Lenovo RackSwitch G8264CS, Руководство по установке

Результаты поиска

Содержание RackSwitch G8264CS

Отзывы:

Похожие инструкции для RackSwitch G8264CS

Бренды по названию

Популярные бренды