Lenovo RackSwitch G8264CS Скачать руководство пользователя страница 64

Страница: 64 / 96

G8264CS Installation Guide

Attention:

If the inlet air temperature is above 35°C (95°F) while the switch is in

operation, replace the fan module within five minutes to avoid overheating the
switch.

To return the component to customer service for replacement, see

Appendix A,

“Getting Help and Technical Assistance

” on

page 79

to help you gather all the

required information that is necessary to return a component. After you remove the

component, securely pack the component for shipping.

Replacing the Fan Module

To replace a hot-swap fan module, complete the following steps:
1. Select an empty fan module bay on the rear of the switch. If the target bay is

covered by a blank fan filler plate, loosen the retainer screw and slide the filler

plate out of the slot.

2. Remove the new fan module from the antistatic shielded bag.
3. Slide the fan module into the card guides in the open slot and gently push it all

the way into the slot, so that it firmly engages with the connector (see the

illustration). Each fan module has a mechanical guide key to prevent you from

inserting the module incorrectly.
For example:

4. Tighten the retaining screw on the fan module. Torque the screw to

approximately 0.25 Nm +/- 0.1 Nm (2 inch-pounds).

5. Make sure that the fan module’s LED is lit.

Retainer Screw

Содержание RackSwitch G8264CS

































































































Результаты поиска

Содержание RackSwitch G8264CS

Отзывы:

Похожие инструкции для RackSwitch G8264CS

Бренды по названию

Популярные бренды

Lenovo RackSwitch G8264CS, Руководство по установке

Результаты поиска

Содержание RackSwitch G8264CS

Отзывы:

Похожие инструкции для RackSwitch G8264CS

Бренды по названию

Популярные бренды