Lenovo RackSwitch G8264CS Скачать руководство пользователя страница 22

Страница: 22 / 96

G8264CS Installation Guide

System Status LEDs

The following table describes the behavior of the system status LEDs:

Note 1:

Support for the stacking feature depends on the installed firmware. To

determine whether your switch supports stacking, see the

Application Guide

for your

specific switch and firmware version.

Note 2:

If service required is due to a stacking error, this LED flashes or is steady

green, depending on its last known good state.

USB Port

The USB port enables you to connect a USB drive to the switch. You can copy files

from the switch to the USB drive, or from the USB drive to the switch. You can also

start the switch using files on the USB drive.

For more information about using the USB drive, see the

Lenovo RackSwitch

G8264CS Release Notes

Table 4. System status LEDs behavior

LED

State

Functional Meaning

All

Off

Total power failure.

- Service

Steady blue

An operational command has been sent to light the

LED so that this device can be more readily located.

Flashing blue

Service is required due to failure of the general system,

its cooling fans, stacking function

, or its power supply.

The specific failure is indicated in conjunction with the

other system status LEDs.

- Power

Steady green

Power is OK.

Flashing green

Power supply failure or disconnection. Service is

required.

- Fans

Steady green

Fans are OK.

Flashing green

Fan failure. Service is required.

- Stacking

Steady green

Device is a Backup/Member in a stack.

Flashing green

Device is the Master in a stack.

Off

Device is not a stacking member.

Содержание RackSwitch G8264CS

































































































Результаты поиска

Содержание RackSwitch G8264CS

Отзывы:

Похожие инструкции для RackSwitch G8264CS

Бренды по названию

Популярные бренды

Lenovo RackSwitch G8264CS, Руководство по установке

Результаты поиска

Содержание RackSwitch G8264CS

Отзывы:

Похожие инструкции для RackSwitch G8264CS

Бренды по названию

Популярные бренды